EL-4PemulaLitar asas

Malapkan LED dengan potentiometer

Tetapkan kecerahan LED dengan memusingkan aci. Potentiometer ialah perintang boleh laras: semasa kamu memusingkan aci, rintangannya berubah antara 0 dan 10 kΩ, dan arus melalui LED turut berubah. Dengan membinanya, kamu belajar mengapa perintang tetap sentiasa ditambah di sebelah pot dan dua kaki mana daripada tiga yang digunakan.

0.0(0)
11 selesai
Malapkan LED dengan potentiometer
Ia dibina dengan bateri 9 V, satu potentiometer 10 kΩ, satu perintang 1 kΩ, satu LED merah dan tiga wayar jumper. Pot dan perintang bersiri dengan LED; arusnya 7 mA apabila rintangan pot sifar dan kira-kira 0.6 mA apabila ia pada nilai tertingginya. Yang kamu pelajari: struktur dalaman potentiometer, menggunakannya sebagai perintang boleh laras dengan dua kaki, tugas perintang siri pelindung dan cara rintangan bersiri dijumlahkan.

Video

Gambar Rajah Litar

Malapkan LED dengan potentiometer - Gambar Rajah Litar

Susun Atur Breadboard

Malapkan LED dengan potentiometer - Susun Atur Breadboard

Langkah Pemasangan

  1. 1

    Place the RV1 potentiometer in the top half above the gap: its three legs go into rows 5, 7 and 9. The legs sit with one row skipped between them. Push the pot down until it is fully seated.

  2. 2

    Get to know the legs: the middle leg (row 7) is the wiper, and the two legs on the sides are the ends of the resistive track. In this circuit the end leg in row 9 and the middle leg are used; the leg in row 5 is left unconnected.

  3. 3

    Connect the top + rail to the top half of row 9 with a jumper wire.

  4. 4

    Plug one leg of R1 (1 kΩ; brown, black, red) into the top half of row 7 and the other leg into the bottom half of row 7. The resistor crosses over the center gap like a bridge.

  5. 5

    Plug the long leg of LED1 into the bottom half of row 7, the same row as the leg of R1.

  6. 6

    Plug the short leg of LED1 into row 8 in the bottom half.

  7. 7

    Connect the bottom half of row 8 to the bottom GND (−) rail with a jumper wire.

  8. 8

    Connect the top GND rail to the bottom GND rail with a jumper wire (at the right end of the breadboard, level with row 29). Because the battery will be connected to the top rails, the bottom rail becomes GND through this bridge.

  9. 9

    Set the shaft of the pot to about the middle position.

  10. 10

    Plug the red wire of the battery clip into the top + rail and the black wire into the top GND (−) rail. Compare the connections with the schematic once, then snap the battery onto the clip.

Petua: biarkan bateri atau bekalan kuasa tidak disambung semasa membuat pendawaian.

Langkah Ujian

  1. 1

    Connect the battery: LED1 must light dimly.

  2. 2

    Turn the shaft slowly in one direction: the LED gets brighter or dimmer. When you turn it the other way, the opposite happens.

  3. 3

    Turn the shaft all the way to the bright end: the LED reaches its brightest and stays steady there. Thanks to R1 the current does not go above 7 mA.

  4. 4

    Turn the shaft all the way to the other end: the LED gets very dim but does not go out completely.

Cara Ia Berfungsi

The potentiometer is an adjustable resistor in series with the LED. As you turn the shaft the total resistance changes between 1 kΩ and 11 kΩ, and the LED current moves between 7 mA and 0.6 mA.

Inside the pot

Between the two end legs of the pot there is an arc-shaped 10 kΩ resistive track. The middle leg travels along this track with a wiper attached to the shaft. As you turn the shaft, the part of the track between the wiper and the end leg gets longer or shorter; the resistance changes between 0 and 10 kΩ.

Series resistances add up

The pot and R1 are connected one after the other, so their resistances add up. The current is found with the formula (9 V − 2 V) / (RV1 + R1). As the pot's resistance grows, the total resistance grows, the current shrinks and the LED dims.

Protective resistor

When the pot's resistance falls to zero, only R1 is left in the circuit and the current is 7 mA. Without R1 there would be nothing left to limit the LED at that moment. An adjustable resistor always gets a fixed resistor next to it that limits the current even in the worst case.

Brightness does not change in equal steps

With the pot exactly in the middle the total resistance is 6 kΩ and the current is about 1.2 mA; that is one sixth of the highest current. Most of the change in current is gathered at the bright end of the rotation. Because the eye picks out differences at small currents well, the LED still seems to dim smoothly.

Formula

  • LED current

    I = (Vbat − VLED) / (RV1 + R1)

    Contoh: Pot in the middle: (9 V − 2 V) / (5 kΩ + 1 kΩ) ≈ 1.2 mA

  • Highest current (RV1 = 0 Ω)

    Imax = (Vbat − VLED) / R1

    Contoh: (9 V − 2 V) / 1 kΩ = 7 mA

  • Lowest current (RV1 = 10 kΩ)

    Imin = (Vbat − VLED) / (RV1 + R1)

    Contoh: (9 V − 2 V) / (10 kΩ + 1 kΩ) ≈ 0.64 mA

Kesilapan Lazim

  • The brightness does not change, the LED is always the same.

    R1 is connected to an end leg of the pot, not to the middle leg. The top leg of R1 must be in row 7.

  • The LED does not light.

    R1 does not join the two sides of the gap, or the bottom GND bridge is missing.

  • The LED is very bright, the pot heats up.

    R1 has been skipped and the pot is connected directly to the LED. Disconnect the battery right away and fit R1 between the middle leg and the LED.

  • The LED is always dim.

    10 kΩ or 100 kΩ is fitted instead of R1. The colors must be brown, black, red.

Soalan Lazim

Mengapakah kaki ketiga pot dibiarkan tidak bersambung?

Di dalam pot ada trek rintangan 10 kΩ antara dua kaki hujung, dan pada kaki tengah ada pengelap yang bergerak di sepanjang trek ini. Untuk melaraskan arus, pengelap dan salah satu hujung sudah memadai. Kamu akan melihat sambungan pembahagi voltan, yang menggunakan ketiga-tiga kaki bersama, dalam litar siri ini yang kemudian.

Tidak bolehkah saya memalapkan LED dengan pot sahaja, tanpa R1?

Ia malap, tetapi tidak selamat. Apabila kamu memusingkan aci hingga ke hujung, rintangan pot jatuh kepada sifar. Pada saat itu, LED disambungkan ke bateri 9 V tanpa rintangan; kedua-dua LED dan trek rintangan nipis di dalam pot boleh terbakar. R1 kekal dalam litar walau di kedudukan mana pun pot berada dan mengehadkan arus kepada paling banyak 7 mA.

Mengapakah LED tidak padam sepenuhnya?

Apabila pot berada pada nilai tertingginya, jumlah rintangan ialah 11 kΩ dan kira-kira 0.6 mA masih mengalir melalui LED. LED memberikan cahaya yang kelihatan walaupun pada arus sekecil ini. Untuk memadamkan LED sepenuhnya, kamu perlu memutuskan arus, iaitu menambah butang atau suis pada litar.

Mengapakah kecerahan berubah begitu pantas di satu hujung putaran?

Arus berkadar songsang dengan jumlah rintangan. Apabila jumlah rintangan naik daripada 1 kΩ kepada 2 kΩ, arus jatuh separuh; itu hanya satu persepuluh daripada putaran. Sepanjang baki putaran, semasa rintangan naik daripada 2 kΩ kepada 11 kΩ, arus jatuh dengan lebih perlahan. Inilah sebabnya kebanyakan perubahan terhimpit di hujung yang terang.