111 projek blok · Arduino · ESP32 · Pico
Pengekodan Blok untuk Projek Arduino, ESP32 dan Pico
Ikuti blok berwarna-warni dan bukannya membaca kod baris demi baris. 111 projek BlueGrays dilengkapi versi blok, dan setiap blok sepadan dengan satu baris kod sebenar yang berjalan pada papan.
Apakah pengekodan blok?
Pengekodan blok bermaksud membina program daripada blok seperti kepingan teka-teki dan bukannya menaipnya. "Tetapkan pin sebagai output", "hidupkan LED" dan "tunggu 1 saat" masing-masing ialah satu blok, dan menyusunnya membentuk program. Tiada koma bertitik, kurungan atau kesilapan menaip untuk dirisaukan, jadi kamu boleh menumpukan pada logik.
BlueGrays menggunakan set bloknya sendiri, dan blok itu bercakap dalam bahasamu: jika aplikasi dalam bahasa Melayu, blok akan menyebut "ulang selama-lamanya" dan "tulis HIGH ke pin". Dalam projek Arduino dan ESP32 blok dipetakan kepada kod C++; dalam projek Raspberry Pi Pico ia dipetakan kepada MicroPython.
Matlamatnya bukan kekal dalam blok selama-lamanya tetapi memahami kod. Letakkan blok sesuatu projek bersebelahan kodnya dan kamu dapat melihat apa yang dilakukan oleh setiap baris. Selepas beberapa projek, kamu mula membaca kod tanpa blok.
Bagaimana pengekodan blok berfungsi dalam BlueGrays
Dalam aplikasi, blok terdapat dalam bahagian kod setiap projek blok. Empat langkah:
- 01
Pilih projek blok
Projek dengan lencana blok dilengkapi versi blok. Kamu juga boleh menapis senarai untuk memaparkan projek blok sahaja.
- 02
Hidupkan "Papar sebagai blok"
Satu suis dalam bahagian kod menukar kod kepada blok. Ketik imej untuk membukanya dalam skrin penuh dan zum masuk.
- 03
Fahami blok
Tab "Fahami blok" membimbing kamu melalui program langkah demi langkah, menunjukkan hanya blok bagi setiap langkah dan fungsinya.
- 04
Beralih kepada kod sebenar
Matikan suis dan program yang sama muncul sebagai kod. Salin ke Arduino IDE (atau Thonny untuk Pico) dan muat naik ke papan kamu.
Satu program: blok dan kod
Di sebelah kiri, blok projek. Di sebelah kanan, kod yang berjalan pada papan. Setiap blok mempunyai baris kod yang sepadan.
Blok

Kod
1// ─────────────────────────────────────────
2// BlueGrays · bluegrays.com
3// LED Blink
4// ─────────────────────────────────────────
5// Blinks a single LED on and off every 100 ms. Shows the basic use of the
6// digitalWrite and delay functions.
7//
8// Pins:
9// D9 -> LED (with a 220 ohm resistor)
10
11void setup() {
12 pinMode(9,OUTPUT); // LED pin as output
13}
14
15void loop() {
16 digitalWrite(9,HIGH); // Turn the LED on
17 delay(100); // Wait 100 ms (1000 ms = 1 s)
18 digitalWrite(9,LOW); // Turn the LED off
19 delay(100);
20}
21Projek blok
Setiap projek dengan versi blok, mengikut platform. Projek percuma di hadapan: 31 daripadanya percuma sepenuhnya, termasuk blok dan kod.
Projek Arduino74 projek blok

LED Blink
The very first hello of electronics: switching a single LED on and off. The Arduino turns the LED on and off at short intervals, so the light blinks quickly.

Two LEDs Blinking Alternately
Two LEDs blink quickly in turn: when one lights up the other goes off, as if they were tossing a ball back and forth.

Traffic Light
A tiny copy of the traffic light you see on the road every day. Red stays on for two seconds, yellow flashes for a moment, green stays on for two seconds, then it goes back to red through yellow…

LED Police Lights
Just like the lights on a police car: the red LED flashes three times in quick succession, then the blue LED flashes three times, and the pattern keeps repeating without a break.

LED Chaser
Lights that switch on one after another, as if they were running. The Arduino lights six LEDs one at a time; each glows for a brief moment and goes out, so the light walks from start to end and then…

Knight Rider LED Effect
The classic scanner light: a dot of light slides from one end of six LEDs to the other and then comes back.

LED Chaser with Adjustable Speed
Six LEDs light up one after another, so the light seems to run from one end to the other.

Knight Rider LED Effect with Adjustable Speed
A light runs from one end of six LEDs to the other, turns around and runs back again.
Projek Arduino: semua projek blok
- AR-9LED Control with a Push Button (Push)Percuma
- AR-10Toggle an LED with a Button (On/Off)Percuma
- AR-11Measuring Light Intensity with an LDRPercuma
- AR-12Night Light with LdrPercuma
- AR-13Using a BuzzerPercuma
- AR-14Frequency Setting with BuzzerPercuma
- AR-27HC-SR04 Distance Measurement (Serial Display)Percuma
- AR-37Reading a Reed SwitchPercuma
- AR-45DS1302 RTC Clock Module SetupPercuma
- AR-55Temperature and Humidity with DHT11Percuma
- AR-613x4 Keypad OperationPercuma
- AR-16Reading IR Remote Control Codes
- AR-17Led On/Off with IR Receiver and Remote Control
- AR-19Lighting 220V Bulb with Push Button
- AR-20Lighting 220V Bulb with Button (On-Off)
- AR-21Lighting 220V Bulb with Remote Control
- AR-22Laser Warning System
- AR-23Laser Security System
- AR-24Motion Detector with Motion Sensor
- AR-25Doorbell and Light with Motion Sensor
- AR-26Simple Piano with Buzzer and Button
- AR-28Parking Sensor with HC-SR04
- AR-29Print Message on 2x16 LCD Screen
- AR-30Bouncing Text Animation on LCD
- AR-31Measuring Distance Using LCD Display
- AR-32Using LCD Screen with I2C
- AR-33Height Measurement Project
- AR-34Control an LED from Your Phone via Bluetooth
- AR-35Using a Servo Motor
- AR-36Servo Motor Operation with Potentiometer
- AR-38Reed Switch Door Sensor
- AR-39Using an RGB LED
- AR-40Smooth Color Transition with RGB Led
- AR-42Displaying Numbers 0-99 on a 7-Segment Display
- AR-43Counter with 7-Segment Display and Buttons
- AR-44Temperature Measurement with NTC and 2x16 Lcd Display
- AR-46DS1302 RTC Clock with LCD Display
- AR-47Displaying 0-9999 on a 4-Digit 7-Segment Display
- AR-48Digital Clock with 4-Digit 7-Segment Display
- AR-49Bomb Animation with 4-Digit 7-Segment Display
- AR-50Using a Flame Sensor
- AR-51Using a Gas Sensor
- AR-52Flame and Gas Sensor Alarm
- AR-53RFID Value Reading
- AR-54RFID Authentication
- AR-56Digital Voltmeter with LCD Display
- AR-58Two-Way Communication Between 2 Arduinos
- AR-59Led Control with Joystick
- AR-60Servo Control with Joystick
- AR-62LED Control with a 3x4 Keypad
- AR-634x4 Keypad Operation
- AR-64Password Lock with 4x4 Keypad and LCD
- AR-67Using a Stepper Motor
- AR-68360-Degree Servo from a Stepper Motor
- AR-69Using a WS2812B LED Strip
- AR-70Police Lights with WS2812B
- AR-71WS2812B LED Chaser
- AR-72WS2812B LED Chaser (Fill Effect)
- AR-73WS2812B Knight Rider Effect
- AR-74WS2812B Knight Rider Effect (3 LEDs)
- AR-75WS2812B Animation 1
- AR-77Reading Reflection (Proximity) with TCRT5000
- AR-78TCRT5000 Black and White Surface Detection
- AR-82Smart Stair and Corridor Lighting
- AR-83Smart Irrigation Station
- AR-95Arduino Reaction Time Test with Sound Cue: Measure Your Reflexes in Milliseconds (LCD + Buzzer + 3 LEDs)
Projek ESP3223 projek blok

LED Blink with ESP32
Teaches basic GPIO output usage with ESP32. We achieve a blinking effect by turning an LED on and off from a digital pin. ESP32 version of the classic blink project on Arduino UNO; the basic blink commands in the Arduino environment are the same, but the ESP32's pin layout and 3.3 V GPIO levels differ from those of the Arduino UNO.

ESP32 LED Control with Push Button (Push)
The LED lights up when the button is pressed and turns off when released. Shows how the ESP32's digital input pin and internal pull-up resistor are used. The INPUT_PULLUP mode eliminates the need for an external resistor.

ESP32 LED Control with Pushbutton (Toggle)
Each time the button is pressed the state of the LED changes: if it is on it turns off, if it is off it turns on. Classic toggle pattern. With debounce we clean up the mechanical noise of the pushbutton to ensure a single toggle with a single press.

ESP32 Built-in LED Blink
Blinking the built-in blue LED on the ESP32 DevKit V1. No external components required! The first project you should try when you buy an ESP32. GPIO 2 is connected to the built-in LED.

ESP32 Traffic Light
Real traffic light simulation with 3 LEDs red-yellow-green. Timings close to real traffic logic: red long, yellow short, green long. Classic example of sequential GPIO control.

ESP32 Knight Rider LED
6 LEDs moving sequentially from left to right and right to left (Knight Rider style). A basic example of using for loops and arrays. Teaches the logic of direction change.

ESP32 LED Fade with PWM
Smoothly changing the brightness of the LED from 0 to max, from max to 0. We control PWM with analogWrite() as in Arduino - the same syntax as ESP32 Arduino Core 3.0+ works without problems. Pin definition + pinMode + analogWrite is enough.

ESP32 RGB LED Control
Unlimited color generation with a single RGB LED instead of 3 separate LEDs. As in Arduino, we make a rainbow transition by setting the R/G/B values with analogWrite(). Color theory (such as red+green=yellow) is seen practically.
Projek ESP32: semua projek blok
- ES-11Reading Light Intensity with the ESP32 LDR ModulePercuma
- ES-14ESP32 HC-SR04 Ultrasonic Distance SensorPercuma
- ES-15ESP32 DHT22 Temperature and Humidity (with LCD Display)Percuma
- ES-20ESP32 MQ-2 Gas/Smoke Detector AlarmPercuma
- ES-21ESP32 RFID RC522 Card Reader (with LCD)Percuma
- ES-7ESP32 Police Strobe Light Effect
- ES-10ESP32 Night Light with LDR
- ES-12ESP32 Melody Playback with Buzzer
- ES-13ESP32 LED Brightness Control with a Potentiometer (Analog → PWM)
- ES-16ESP32 Servo Motor (Potentiometer Control)
- ES-17ESP32 I2C LCD Display (16x2)
- ES-18Digital Clock with ESP32 and DS1307 RTC (I2C + LCD)
- ES-19Automatic Lighting with the ESP32 PIR Motion Sensor
- ES-23ESP32 TM1637 4-Digit 7-Segment Display
- ES-24ESP32 WS2812B NeoPixel Strip Control
Projek Raspberry Pi Pico10 projek blok

Raspberry Pi Pico Onboard LED Blink (Pico and Pico W)
The opening project of the Raspberry Pi Pico series! We blink the Pico's green built-in LED to confirm the board works, the classic "Hello World" first experiment. No external parts needed, just the Pico and a USB cable. The code is written in MicroPython, the language officially supported by the Raspberry Pi Foundation.

Raspberry Pi Pico: Controlling an External LED (Breadboard)
The next step after the Pico's built-in LED: connect an external LED on a breadboard and control it through pin GP14. You'll learn how to use any of the Pico's GPIO pins as an output, the LED's polarity (long leg = anode/+, short leg = cathode/–) and why a current-limiting resistor (220Ω) is a must. Without the resistor, too much current flows through the LED and it can burn out.

Raspberry Pi Pico Alternating Two LEDs (Blink-Flip Pattern)
The next step after the Pico's single LED: the classic flip-flop animation, with two LEDs blinking in turn. One LED turns off as the other turns on, the most basic example of handling multiple GPIOs. Two LEDs of different colors (red on GP14, green on GP13) swap every 500 ms. With MicroPython's Pin.toggle() method, the code stays short and readable.

Raspberry Pi Pico Traffic Light Simulator (3 LEDs Sequential)
We recreate real traffic light logic with red, yellow and green LEDs, the first Pico project to move up to 3 LEDs! Green says "go" for 4 seconds, yellow "get ready" for 1.5 seconds, red "stop" for 3 seconds, and red+yellow "set off" for 1 second (the European traffic light pattern). You'll learn to define functions (def all_off()), state machine logic and multi-GPIO synchronization.

Raspberry Pi Pico Police Strobe Light Effect (Red + Blue)
We simulate a police car's light bar with a Raspberry Pi Pico in its simplest form! The red and blue LEDs take turns (flip-flop): while red is on, blue is off, and they swap every 0.3 seconds, forever. The code writes the two steps directly in a single while True loop; the speed is set with the WAIT_MS constant.

Raspberry Pi Pico 3-Burst Police Flip-Flop (2 LEDs)
Rhythmic variation of the police strobe project — 3-burst flip-flop! Same 2-LED circuit (GP11 red + GP12 blue), but a different pattern: red LED flashes 3 times rapidly, then blue flashes 3 times, forever. This "burst + switch" pattern is the most recognizable rhythm of real police siren lights. Learn parametrized function def burst(led, count, duration_ms), rhythm design, and generating different visual effects with code on same circuit.

Raspberry Pi Pico Button Toggle LED
Button + LED — next level! Unlike the basic button project, there is no need to hold the button. Press and release → LED on. Press and release again → LED off (toggle). Same circuit (LED GP14, Button GP2), but big code difference. Learn edge detection (capturing the 1→0 falling moment), state tracking, debounce (mechanical bounce filter). MicroPython's led.toggle() swaps state in one line. Foundation of all interactive button projects (mode switcher, IRQ, double-click).

Raspberry Pi Pico PWM LED Fade (Breathing Effect)
The LED doesn't just blink anymore, it breathes! With the Raspberry Pi Pico's PWM (Pulse Width Modulation), the LED's brightness slowly rises and then slowly fades, a calm "breathing" effect like a sleeping laptop's light. You'll learn the machine.PWM class, the 16-bit brightness value from 0–65535 with duty_u16() and the PWM frequency.
Projek Raspberry Pi Pico: semua projek blok
Untuk siapa?
Kanak-kanak dan ibu bapa
Pengekodan untuk kanak-kanak lebih melekat jika berakhir dengan LED yang menyala di atas meja. Blok menjadikan program mudah dibaca, dan kamu membina litar bersama-sama.
Guru dan kelab
Dalam kelas robotik atau STEM kamu boleh menerangkan projek dengan blok dahulu, kemudian beralih kepada kodnya. Setiap projek mempunyai senarai komponen dan gambar rajah litar yang sedia ada.
Pemula
Pengekodan blok Arduino ialah cara terpantas untuk memahami logik dalam beberapa projek pertama kamu. Mulakan dengan blok dan beralih kepada kod apabila kamu rasa bersedia.
Soalan lazim
Apakah pengekodan berasaskan blok?
Ia ialah cara pengaturcaraan yang arahannya dipaparkan sebagai blok yang disambung seperti kepingan teka-teki dan bukannya teks yang ditaip. Oleh kerana kesilapan menaip tidak mungkin berlaku, pemula dan kanak-kanak lebih mudah memahami logik sesuatu program.
Berapa banyak projek BlueGrays yang dilengkapi blok?
Buat masa ini 111: 76 projek Arduino, 25 ESP32 dan 10 Raspberry Pi Pico. Senarai bertambah apabila lebih banyak projek ditukar.
Adakah pengekodan blok percuma?
Aplikasi ini percuma. Blok dan kod 31 projek blok terbuka kepada semua orang. Dalam projek lain, blok dibuka dengan Premium, sama seperti kod.
Bolehkah saya memuat naik blok terus ke papan saya?
Tidak. Blok menjadikan program lebih mudah dibaca dan difahami; apa yang masuk ke papan sentiasa kod sebenar projek itu. Kamu menyalinnya ke Arduino IDE, atau Thonny untuk Pico, dan memuat naiknya.
Bolehkah saya membina program sendiri dengan blok?
Belum lagi. Kami menyediakan blok untuk setiap projek dan memadankannya dengan kod satu lawan satu, jadi blok yang kamu lihat sentiasa mewakili program yang telah diuji dan berfungsi.
Apakah bezanya dengan Scratch atau mBlock?
Dalam Scratch dan mBlock kamu menyeret blok pada komputer untuk menulis program sendiri. Dalam BlueGrays setiap projek blok dilengkapi gambar rajah litar, senarai komponen dan kod sebenar, dan blok ialah versi kod itu yang mudah dibaca. Kedua-duanya saling melengkapi.
Adakah sesuai untuk kanak-kanak? Pada umur berapa mereka boleh bermula?
Kanak-kanak sekitar 9 atau 10 tahun yang boleh membaca dengan baik boleh bermula bersama orang dewasa. Projek pertama tidak memerlukan pateri: ia dibina pada breadboard dengan LED, butang dan buzzer.
Dalam bahasa apakah blok itu?
Bahasa Inggeris, Turki, Jerman, Sepanyol, Perancis dan Itali, termasuk Melayu. Blok dipaparkan dalam bahasa yang kamu gunakan untuk aplikasi.

