AR-45Pemula

Persediaan modul jam RTC DS1302

4.5(23)
31 selesai
Persediaan modul jam RTC DS1302
Hidupkan modul jam kecil yang terus menyimpan waktu walaupun Arduino dimatikan. Modul ini mempunyai bateri kecilnya sendiri. Selepas waktu ditetapkan sekali, tarikh dan waktu dipaparkan pada skrin komputer setiap saat. Projek penggera, pemasa dan projek yang menyimpan rekod semuanya bermula dengan langkah ini.

Video

Gambar Rajah Litar

Persediaan modul jam RTC DS1302 - Gambar Rajah Litar

Kod Sumber

C++ (Arduino IDE)
1// ─────────────────────────────────────────
2//   BlueGrays · bluegrays.com
3//   DS1302 RTC Clock Module Setup
4// ─────────────────────────────────────────
5// If the RTC's time is invalid (new module, flat battery) it writes the
6// compile date and time to the DS1302 once, then prints the date and time
7// to the Serial Monitor every second. The module's battery keeps the time
8// with the power off; later starts do not set it again.
9//
10// Pins:
11//   D6 -> RTC CLK
12//   D7 -> RTC DAT
13//   D8 -> RTC RST
14//   RTC VCC to 5V, GND to GND
15
16#include <virtuabotixRTC.h>   // DS1302 library
17
18// Pins: CLK, DAT, RST
19virtuabotixRTC myRTC(6, 7, 8);
20
21void setup() {
22  Serial.begin(9600);   // Serial at 9600 baud
23
24  // Read the RTC first. A year below 2024 or a month outside 1-12 means the time was never set;
25  // write the compile time. If it is valid leave it, so uploading again or power cycling the
26  // Arduino keeps the time.
27  myRTC.updateTime();
28  if (myRTC.year < 2024 || myRTC.month < 1 || myRTC.month > 12) {
29    setFromCompileTime();
30  }
31}
32
33// Writes the compile time (__DATE__ "Oct 28 2026", __TIME__ "13:42:15") to the RTC. Uploading takes
34// a few seconds, so the clock starts that far behind.
35void setFromCompileTime() {
36  const char *date = __DATE__;
37  const char *time = __TIME__;
38  const char *months = "JanFebMarAprMayJunJulAugSepOctNovDec";
39  char monthName[4] = {date[0], date[1], date[2], '\0'};
40
41  int month = (strstr(months, monthName) - months) / 3 + 1;   // "Oct" -> 10
42  int day = atoi(date + 4);
43  int year = atoi(date + 7);
44  int hour = atoi(time);
45  int minute = atoi(time + 3);
46  int second = atoi(time + 6);
47
48  // Day of the week (Sakamoto's method), 0 = Sunday
49  int offsets[] = {0, 3, 2, 5, 0, 3, 5, 1, 4, 6, 2, 4};
50  int y = year - (month < 3);
51  int weekday = (y + y / 4 - y / 100 + y / 400 + offsets[month - 1] + day) % 7;
52  if (weekday == 0) {
53    weekday = 7;   // Monday = 1 ... Sunday = 7
54  }
55
56  // Order: s, min, h, weekday, day, month, year
57  myRTC.setDS1302Time(second, minute, hour, weekday, day, month, year);
58}
59
60void loop() {
61  // Read the current time from the RTC module
62  myRTC.updateTime();
63
64  // Print the time (day/month/year h:m:s)
65  Serial.print("Current Date/Time: ");
66  Serial.print(myRTC.dayofmonth);
67  Serial.print("/");
68  Serial.print(myRTC.month);
69  Serial.print("/");
70  Serial.print(myRTC.year);
71  Serial.print("  ");
72  Serial.print(myRTC.hours);
73  Serial.print(":");
74  Serial.print(myRTC.minutes);
75  Serial.print(":");
76  Serial.println(myRTC.seconds);
77
78  delay(1000);   // Wait 1 s
79}
80

Soalan Lazim

Apakah kegunaan modul RTC?

Modul jam masa nyata (RTC) terus menyimpan waktu dan tarikh walaupun Arduino dimatikan, dengan bantuan bateri pada modul. Oleh sebab pembilang millis() Arduino ditetapkan semula setiap kali Arduino dihidupkan, RTC diperlukan untuk mendapatkan waktu sebenar.

Adakah menetapkan waktu sekali sahaja sudah mencukupi?

Ya. Kod membaca waktu daripada modul terlebih dahulu. Jika waktu belum pernah ditetapkan, kod menulis tarikh dan waktu ketika kamu mengkompil kod, sekali sahaja. Jika waktu itu sah, kod membiarkannya tanpa perubahan. Jadi, memuat naik kod semula atau mematikan dan menghidupkan Arduino tidak mengganggu jam. Kamu tidak perlu menukar mana-mana baris kod menjadi komen secara manual.

Waktu jam semakin tersasar, adakah ini normal?

DS1302 menggunakan kristal dan waktunya boleh tersasar beberapa saat sehari. Untuk jam yang lebih tepat, modul DS3231 dengan pampasan suhu disyorkan (kira-kira ±1 minit setahun).

Apakah yang berlaku apabila bateri modul habis?

Jam berfungsi selagi Arduino menerima bekalan kuasa. Jika bekalan kuasa terputus dan bateri juga habis, jam akan ditetapkan semula dan waktunya perlu dilaraskan semula. Bateri CR2032 biasanya tahan beberapa tahun.