Teroka Projek Arduino
Ratusan projek dari pemula hingga mahir: gambar rajah litar, kod dan video. Mulakan di tahap mana pun kamu berada.

Arduino Remote-Controlled Shadow Play: Hacivat and Karagöz (IR + 2 Servos + 2 LEDs)
A traditional Turkish shadow play run by a TV remote: two SG90 servos hold the rods of Hacivat and Karagöz, while a yellow and an orange LED behind the curtain flicker like an oil lamp. Keys 1, 2, 3 play a greeting, a chase and a farewell scene; the arrow keys let you move the puppets by hand, and POWER switches the curtain light. The lines show up on the serial monitor in Turkish and English. A ready-made puppet theatre for a school show.

ESP32 Baby Cradle Rocker (Servo + I2C LCD + 2 Buttons + Buzzer)
A helper for tired parents: an SG90 servo rocks a toy cradle with a soft, sine-like swing while a buzzer quietly plays Brahms' Lullaby. Two buttons give you 3 speeds (SLOW, MEDIUM, FAST), lullaby on/off and a 10, 20 or 30 minute timer, and the I2C LCD shows the mode and the time left. When time is up the cradle never stops dead: the swing fades out slowly and the lullaby slows to its end.

Raspberry Pi Pico W Tea Bag Dipper: Light, Medium, Strong (Servo + Pot + 3 LEDs + Buzzer)
No more bitter tea from a forgotten tea bag: with a Raspberry Pi Pico W, an SG90 servo lowers the bag into your cup, dips it now and then and lifts it out when the time is up. You pick the strength with a potentiometer: LIGHT 2 min, MEDIUM 3 min, STRONG 5 min. There is no button; turn the pot, let go for 2 seconds and brewing starts. 3 LEDs show the time left, and a buzzer plays our own "tea is ready" tune at the end.

ESP32 Blooming Tulip Lamp: Opens at a Touch (Servo + 24 LED Ring + TTP223)
The maker world's favourite blooming flower lamp, with a Tulip Era twist: touch the TTP223 sensor and an SG90 servo slowly opens the petals on a soft speed curve while a 24 LED ring fades in from darkness. While it is open, every touch changes the colour: red, purple, yellow, warm white and a tulip garden that drifts around the ring. Hold it and the tulip closes as the light fades out.

Arduino Biting Crocodile: Which Tooth? (8 Buttons + Servo Jaw + Buzzer)
A party game in the style of the classic biting-crocodile toy: eight buttons are the crocodile's teeth and an SG90 servo is its upper jaw. Each round one tooth is secretly cursed. You take turns pressing teeth; a safe tooth clicks and the jaw twitches a little. Whoever presses the cursed tooth gets bitten: the jaw snaps shut, the red eye lights up and the buzzer growls. As fewer teeth are left, the green eye blinks faster and faster.

Raspberry Pi Pico W Toy Fire Truck Ladder: Siren, Flashing Lights and a Rising Ladder (Servo + 4 LEDs + 2 Buttons + Buzzer)
A desktop toy fire truck with a Raspberry Pi Pico W. Press the red button and a two-tone siren rises and falls while two red and two blue LEDs flash to the same beat. Press the yellow button and an SG90 servo slowly raises the ladder; press again to lower it, with a warning beep while it moves. Both work together, and a forgotten siren stops by itself after 60 seconds.

Arduino Singing Snowman: Waves When You Approach and Dances (HC-SR04 + 2 Servos + 2 LEDs + Buzzer)
A snowman that comes alive for a shop window or a school door. The HC-SR04 measures who is in front: within 1 metre the blue LED eyes light up, the right arm waves and the buzzer says "hello". Within 30 cm it plays Jingle Bells, the two servo arms rise in turn to the beat and the eyes flash on every note. When the person walks away, the left arm waves goodbye; with nobody around the eyes blink slowly.

Arduino Model Railway Turnout and Signal Remote (IR + 2 Servos + 4 LEDs)
Throw the two turnouts of your model railway with a TV remote: two SG90 servos move the point blades slowly, just like real points, and each turnout has a red/green signal. While a turnout moves its signal shows red, once it locks in place it turns green. 1 sets the main line, 2 the siding, and the turnouts move one after the other; the arrow keys switch a single turnout and POWER is an emergency stop. Positions are kept in EEPROM, so the servos do not jump at power-up.

Pico W IoT Motion Counter (PIR)
Count how many times someone walks through a door or hallway, and see the moment of motion live on your phone. This project is the step-by-step guide to the Motion detector IoT template in the app, built with a Raspberry Pi Pico W and a PIR motion sensor using just 3 wires. Go to Workshop › Devices › Add a device; Ohmi prepares the code with your own device key. The code on this page is an example: the key and Wi-Fi details are placeholders.

ESP32 Bluetooth Car (L298N)
Drive a two-wheel car over Bluetooth with the joystick on your phone; no internet needed, works on iPhone and Android. This project is the step-by-step guide to the Car remote Bluetooth template in the app, built with an ESP32, an L298N and two motors. Go to Workshop › Devices › Add a device › Bluetooth, pick Car remote and upload the code from Get the code. The Set up as a Bluetooth panel button on this page opens the wizard with this template.

ESP32 Bluetooth Servo Lock
Control an SG90 servo as a small latch from your phone over Bluetooth: lock, open or set the angle, no internet or Wi-Fi needed. This project is the step-by-step guide to the Servo lock Bluetooth template in the app, built with an ESP32, one servo and 3 wires. Go to Workshop › Devices › Add a device › Bluetooth, pick Servo lock and upload the code with Get the code. The Set up as a Bluetooth panel button on this page opens the wizard with this template too.
