Teroka Projek Arduino
Ratusan projek dari pemula hingga mahir: gambar rajah litar, kod dan video. Mulakan di tahap mana pun kamu berada.

Laser Warning System
You set up an invisible beam fence, just like in the movies. A laser shines onto a light sensor on the other side; the moment someone walks through and breaks the beam, the LED lights up and the…

Doorbell and Light with Motion Sensor
When someone comes up to your door, you know before they even ring. As soon as the motion sensor spots someone, the LED lights up and the buzzer plays a three-note chime from high to low; when the…

Using a Flame Sensor
A little guard that spots fire before you do, in the kitchen or the workshop. The flame sensor picks up the invisible light that fire gives off; while all is well the green LED is on, and when it…

RFID Authentication
Just like the card entry at an apartment door: you hold your card near the RFID reader, and the Arduino compares its number with the one it has saved.

Smart Stair and Corridor Lighting
Step onto the stairs or into the hallway and the lights come on one step at a time in the direction you are walking.

Automatic Lighting with the ESP32 PIR Motion Sensor
In this project an HC-SR501 PIR motion sensor detects someone entering the room and turns on an LED automatically. millis() tracks how long the LED stays on: each HIGH reading refreshes the last-motion time, and the LED turns off at least 10 seconds after the last HIGH. The code also waits 50 ms with delay(50) in every loop, so the loop is not fully non-blocking. Great for stairs, hallways, bathrooms or closet lighting.

ESP32 MQ-2 Gas/Smoke Detector Alarm
In this project, combustible gas (LPG, methane, propane) and smoke detection is performed using an MQ-2 gas sensor module, and a siren-like alarm is played through a passive buzzer upon detection. The sensor's digital threshold output (DO) is connected to GPIO 4 on the ESP32; when gas or smoke exceeds the threshold, DO goes LOW and the alarm is triggered. Sensitivity is adjusted via the module's potentiometer. The passive buzzer is driven using tone() to produce a two-frequency siren effect.

ESP32 RFID RC522 Card Reader (with LCD)
In this project, we will connect the MFRC522-based RC522 RFID module to the ESP32 via SPI and read the card/tag UID. This forms the basis for applications such as door locks, membership systems, and access control. We will display the read UID on an LCD screen; this version does not compare it with an authorized card list. WARNING: The RC522 operates only at 3.3V; supplying 5V will burn out the module!

Raspberry Pi Pico LED Campfire (8x8 NeoPixel Matrix + Potentiometer + Buzzer)
A campfire that doesn't burn or warm anything, but still crackles! The Raspberry Pi Pico draws a realistic flame on an 8x8 NeoPixel matrix, recalculated every frame: sparks appear at the base, heat cools as it rises and glows from red to white. A potentiometer sets the flame height, a button switches between Fire, Gas, Magic and Amethyst themes, and a buzzer adds the crackle of burning wood. Procedural animation, ADC, PWM and MicroPython in one project.

Raspberry Pi Pico Keypad Lock (4x4 Keypad + I2C LCD + Servo)
A 4-digit code opens the door, and three wrong tries mean a 30 second wait! The Raspberry Pi Pico checks the PIN typed on a 4x4 keypad: if it's right, an SG90 servo unlocks and relocks by itself after 5 seconds. An I2C LCD shows the stars, the tries left and the countdown, and a buzzer beeps on every key. The default PIN is 1234; change it with the A key and the new one is saved to pin.txt.

ESP32 Earthquake Shake Alarm (MPU-6050 + OLED Display + Buzzer)
When your desk shakes, this screen notices first! The ESP32 measures vibration with an MPU-6050 accelerometer and draws a live trace that scrolls like a seismograph on a 0.96-inch OLED display. When the shaking passes the threshold, a passive buzzer sounds a siren and the red LED flashes; one button silences and resets it. It is an educational shake meter, not an official earthquake warning.

ESP32 Prayer Time Clock (Wi-Fi + OLED Display + Buzzer)
How long until Maghrib? The ESP32 gets the time from the internet, pulls your city's prayer times using the Diyanet method and shows the next prayer with a big countdown on a 0.96 inch OLED. When the time comes, a passive buzzer plays a short, gentle chime. Press the button to list all of today's times, or hold it to try the alert right away in demo mode.
