Relay
Komponentlar

Relay

4.5(29)
30
A relay is a switching device used to receive low current signals and control high current devices.

Bu komponent ishlatiladigan loyihalar

Lighting 220V Bulb with Remote Control
AR-21Yuqori
Premium

Lighting 220V Bulb with Remote Control

Switch a real light bulb in your home on and off with a TV remote, without getting up from the sofa.

4.4(23)
31
Smart Irrigation Station
AR-83Yuqori
Premium

Smart Irrigation Station

A gardener that waters your plants on its own, so they don't dry out while you're on vacation.

5.0(42)
57
Lighting 220V Bulb with Push Button
AR-19Yuqori
Premium

Lighting 220V Bulb with Push Button

As long as you hold the button, a real 220-volt bulb stays lit, and it goes out the moment you let go.

4.4(30)
38
Lighting 220V Bulb with Button (On-Off)
AR-20Yuqori
Premium

Lighting 220V Bulb with Button (On-Off)

Want to switch a real household bulb on and off with a tiny button? Each time you press the button, the Arduino flips a relay and the bulb lights up; press again and it goes off.

4.5(33)
44
ESP32 Smart Lighting (PIR + LDR + Relay + OLED)
ES-37Yuqori
Premium

ESP32 Smart Lighting (PIR + LDR + Relay + OLED)

With an ESP32, a PIR motion sensor, an LDR light sensor and a relay module, we turn your hallway, bathroom or pantry into smart lighting. If the room is already bright, the light stays off even when there is motion, so it never wastes energy during the day. The light stays on for 30 seconds, and the time extends automatically while motion continues.

4.3(6)
11
Arduino Smart Thermostat (DHT22 + Relay + I2C LCD)
AR-107O‘rta
Premium

Arduino Smart Thermostat (DHT22 + Relay + I2C LCD)

Room at 19 degrees, target 21: the relay clicks on! The DHT22 measures the temperature, and when it drops below the target the relay turns the heater on. Thanks to hysteresis, the relay does not keep clicking around the target. Two buttons set the target in 0.5 °C steps, and it is kept in EEPROM; the I2C LCD shows temperature, humidity and heater state. The basics of real home automation in one project.

5.0(1)
1
Raspberry Pi Pico IR Remote Control for an LED and a Relay (IR Receiver + Relay + LED)
PI-36O‘rta
Premium

Raspberry Pi Pico IR Remote Control for an LED and a Relay (IR Receiver + Relay + LED)

Turn the light on with a remote! We are building a remote-controlled LED and socket with a Raspberry Pi Pico, an IR receiver and a relay. 1 toggles the relay, 2 the LED; + and − change the LED brightness in 5 steps, PLAY starts a breathing mode and 3 runs the relay on a timer. NEC codes are decoded without a library, from pulse times measured with an interrupt.

ESP32 Egg Incubator Controller (DHT22 + Relay + Servo + OLED)
ES-54O‘rta
Premium

ESP32 Egg Incubator Controller (DHT22 + Relay + Servo + OLED)

Hand the hen's job to an ESP32! The DHT22 measures temperature and humidity, a relay switches the heater with hysteresis, an SG90 servo gently tilts the egg tray every 3 hours, and the 0.96 inch OLED shows the day counter, a temperature graph and alarms. Chicken, quail and duck profiles are built in, and turning stops by itself for the last 3 days. If the sensor fails, the heater switches off for safety.

Raspberry Pi Pico Water Tank Level Gauge and Automatic Pump (HC-SR04 + OLED + Relay)
PI-41O‘rta
Premium

Raspberry Pi Pico Water Tank Level Gauge and Automatic Pump (HC-SR04 + OLED + Relay)

A smart gauge that measures the water level without ever touching the water! An HC-SR04 measures the distance from the tank lid to the water, and the Raspberry Pi Pico turns it into percent and liters. At 20% the relay starts the pump and stops it at 95%; if no water comes or the tank overflows, the buzzer sounds an alarm. The OLED shows a rippling tank drawing, the flow rate and the time left to fill.

Arduino Automatic School Bell (DS1307 + I2C LCD + Relay)
AR-118O‘rta
Premium

Arduino Automatic School Bell (DS1307 + I2C LCD + Relay)

Now the Arduino rings the school bell! A DS1307 keeps the time, and the lesson, break, lunch and home-time bells ring on their own from a schedule table. A relay drives the real bell, a buzzer plays a different tune for each bell type and an I2C LCD counts down to the next bell. It also has exam and holiday modes, a manual bell, clock setting with two buttons and the Turkish National Anthem for the Monday and Friday ceremonies.

Arduino Countdown Socket Timer (KY-040 Rotary Encoder + I2C LCD + Relay)
AR-126O‘rta
Premium

Arduino Countdown Socket Timer (KY-040 Rotary Encoder + I2C LCD + Relay)

Pick a time, press, and let the timer do the rest! The KY-040 rotary encoder sets anything from 5 seconds to 12 hours, and turning fast jumps in 10-minute steps. The relay has three modes: off when time is up, on when time is up, or an on/off cycle. The I2C LCD shows the time left, beeps warn you in the last seconds, the last setting is kept in EEPROM and the relay always starts safely off after a power cut.

ESP32 Wi-Fi Plant Watering: Waters When the Soil Dries, Tells Your Phone (Soil Moisture Sensor + Relay + Pump + LCD + ntfy)
ES-85O‘rta
Premium

ESP32 Wi-Fi Plant Watering: Waters When the Soil Dries, Tells Your Phone (Soil Moisture Sensor + Relay + Pump + LCD + ntfy)

Automatic plant watering with an ESP32: the soil moisture sensor is turned into a percentage, and when it drops the relay runs the pump in short pulses, waits for the water to soak in and measures again. A float switch locks the pump when the tank is empty, and a daily limit prevents flooding. After every watering your phone gets "Bitki sulandi (nem %28 -> %65)"; watering keeps going even without Wi-Fi.

Tegishli asboblar