Bu komponent ishlatiladigan loyihalar

Using a WS2812B LED Strip
Meet a smart LED strip where you can colour every single light on its own. The Arduino first lights the first five LEDs red, a second later turns the other five blue, then switches them all off and…

Police Lights with WS2812B
You bring the red and blue lights from the roof of a police car right onto your desk.

WS2812B LED Chaser
On a strip of ten LEDs, a green dot of light moves from start to finish one LED at a time, then jumps back to the beginning; it stays on each LED for a third of a second.

WS2812B LED Chaser (Fill Effect)
A light strip that fills up and empties like a glass of water. The Arduino lights ten color LEDs one by one in orange and keeps them on; once the strip is full, it switches them off one by one in the…

WS2812B Knight Rider Effect
A red dot of light slides from one end of a smart LED strip to the other, then comes back, sweeping back and forth without ever stopping.

WS2812B Knight Rider Effect (3 LEDs)
All the colours of the rainbow glide slowly along a strip of 56 LEDs. Each LED glows in a slightly different colour from its neighbour and the colours keep flowing in the same direction, turning the…

WS2812B Animation 2
Set up a light show in your room that changes colors all by itself. The Arduino keeps colors flowing along a 30-LED strip and switches to a new color set every few seconds: rainbow, purple and green…

WS2812B Animation 1
On a strip of 56 LEDs, all the colours of the rainbow line up side by side and flow without ever stopping, as if a river of light were gliding along the strip.

ESP32 WS2812B NeoPixel Strip Control
WS2812B (NeoPixel) addressable LEDs are smart RGB LEDs that can be chained and controlled from a single data pin. In this project we drive an 8-LED WS2812B strip with the Adafruit_NeoPixel library and create a smooth rainbow animation. The ESP32's 3.3V logic works with most WS2812B batches; if it gets unstable, we show the fix with a 470Ω series resistor and a 1000µF capacitor. The animation shifts the hue in HSV color space.

Raspberry Pi Pico LED Tug of War Game (NeoPixel Strip + 2 Buttons + Buzzer)
A two-player button duel! The Raspberry Pi Pico turns a 30-LED WS2812B NeoPixel strip into a rope: red player on the left, blue player on the right. Every press pushes your color one LED forward; fill the whole strip to win the round, and take 3 rounds to win the match. Press too early in the countdown and you lose ground, the passive buzzer gives each player a different click, and the match ends in a rainbow. neopixel, debouncing and non-blocking sound in MicroPython.

ESP32 Ambient TV Backlight (ILI9341 TFT + WS2812B LED Strip)
A TV backlight that spills the colors of the screen edges onto the wall! A 2.8 inch ILI9341 display plays the TV with six scenes; the ESP32 averages the color of each edge zone and sends it to a 34-LED WS2812B strip along the left, top and right. Exponential smoothing and gamma correction keep the fades soft, a potentiometer sets the brightness and a button switches between demo, warm white, colors from the computer and off.

Arduino Light Saber (MPU-6050 + WS2812B LED Strip + Buzzer)
Press the button and the light shoots from the hilt to the tip with a "vzzz"! A 30-LED WS2812B strip is the blade, an MPU-6050 measures how fast the sword turns and when it hits something, and a passive buzzer plays the hum. Swing it and the hum rises while the blade glows brighter; hit something and it flashes white with a crackle. A long press cycles through six colours, and your pick is remembered after power-off.

