ESP32 Bluetooth mashina (L298N)
Ikki g‘ildirakli mashinani telefoningdagi joystik bilan Bluetooth orqali boshqar; internetsiz, iPhone va Android-da ishlaydi. Bu loyiha ilovadagi Mashina pulti Bluetooth shabloni uchun ESP32, L298N va ikkita motor bilan qadamma-qadam qo‘llanma. Ustaxonam › Qurilmalar › Qurilma qo‘shish › Bluetooth bo‘limiga o‘t, «Mashina pulti»ni tanla va kodni Kodni olish orqali yukla. Sahifadagi Bluetooth paneli sifatida o‘rnatish tugmasi sozlash ustasini shu shablon bilan ochadi.

Video
Elektr sxemasi

Manba kodi
1// ┌───────────────────────────┐
2// │ BlueGrays · bluegrays.com │
3// │ Bluetooth · ESP32 │
4// │ BG-Araba │
5// └───────────────────────────┘
6// Car remote
7// Arduino IDE board: ESP32 Dev Module
8// the BLE library comes with the ESP32 board package, nothing extra to install
9
10#include <BLEDevice.h>
11#include <BLEServer.h>
12#include <BLE2902.h>
13
14const char BLE_NAME[] = "BG-Araba"; // the board advertises with this name, the app finds it in the list by it
15
16// Pins: change them here if you wired differently
17const int ENA = 14, IN1 = 27, IN2 = 26; // Motor A (ENA, IN1, IN2) is the left wheel, motor B (ENB, IN3, IN4) the right one
18const int ENB = 32, IN3 = 25, IN4 = 33;
19const unsigned long COMMAND_TIMEOUT_MS = 500; // Safety: the motors stop if no command arrives for 500 ms (the app repeats it while you drive)
20
21void btWrite(const char *text);
22void onValue(const char *key, const char *value);
23void sendAll();
24void onLinkLost();
25
26// ── The app sends "key=value" lines; on "?" the board sends all its values ──
27char line[65];
28uint8_t lineLen = 0;
29unsigned long lastRxMs = 0;
30
31bool is(const char *a, const char *b) { return strcmp(a, b) == 0; }
32bool isOn(const char *v) { return v[0] == '1'; }
33
34void sendText(const char *key, const char *value) {
35 char out[72];
36 snprintf(out, sizeof(out), "%s=%s\n", key, value);
37 btWrite(out);
38}
39
40void sendInt(const char *key, long value) {
41 char text[12];
42 snprintf(text, sizeof(text), "%ld", value);
43 sendText(key, text);
44}
45
46void sendFloat(const char *key, float value) {
47 char text[16];
48 dtostrf(value, 1, 1, text);
49 sendText(key, text);
50}
51
52void handleLine(char *text) {
53 char *eq = strchr(text, '=');
54 if (eq == nullptr) {
55 if (text[strlen(text) - 1] == '?') {
56 btWrite("@v=1.0\n"); // the "@v" line tells the app the code version
57 sendAll();
58 }
59 return;
60 }
61 *eq = '\0';
62 onValue(text, eq + 1);
63}
64
65void feed(char c) {
66 lastRxMs = millis();
67 if (c == '\n' || c == '\r') {
68 if (lineLen == 0) return;
69 line[lineLen] = '\0';
70 lineLen = 0;
71 handleLine(line);
72 } else if (lineLen < sizeof(line) - 1) {
73 line[lineLen++] = c;
74 }
75}
76
77// ── Bluetooth (Nordic UART) ──
78#define UART_SERVICE "6E400001-B5A3-F393-E0A9-E50E24DCCA9E"
79#define UART_RX "6E400002-B5A3-F393-E0A9-E50E24DCCA9E"
80#define UART_TX "6E400003-B5A3-F393-E0A9-E50E24DCCA9E"
81
82BLECharacteristic *txChar = nullptr;
83volatile bool linked = false;
84volatile bool linkLost = false;
85// incoming bytes move from the Bluetooth task to loop() through a small ring buffer
86const int RX_SIZE = 256;
87volatile uint8_t rxBuf[RX_SIZE];
88volatile int rxHead = 0, rxTail = 0;
89
90class ServerEvents : public BLEServerCallbacks {
91 void onConnect(BLEServer *server) override { linked = true; }
92 void onDisconnect(BLEServer *server) override { linked = false; linkLost = true; }
93};
94
95class RxEvents : public BLECharacteristicCallbacks {
96 void onWrite(BLECharacteristic *c) override {
97 auto v = c->getValue();
98 for (size_t i = 0; i < v.length(); i++) {
99 int next = (rxHead + 1) % RX_SIZE;
100 if (next == rxTail) break;
101 rxBuf[rxHead] = (uint8_t)v[i];
102 rxHead = next;
103 }
104 }
105};
106
107// lines go out in 20-byte packets (works with every phone)
108void btWrite(const char *text) {
109 if (!linked || txChar == nullptr) return;
110 size_t n = strlen(text);
111 for (size_t i = 0; i < n; i += 20) {
112 size_t len = n - i < 20 ? n - i : 20;
113 txChar->setValue((uint8_t *)text + i, len);
114 txChar->notify();
115 delay(4);
116 }
117}
118
119void btBegin() {
120 BLEDevice::init(BLE_NAME);
121 BLEServer *server = BLEDevice::createServer();
122 server->setCallbacks(new ServerEvents());
123 BLEService *uart = server->createService(UART_SERVICE);
124 txChar = uart->createCharacteristic(UART_TX, BLECharacteristic::PROPERTY_NOTIFY);
125 txChar->addDescriptor(new BLE2902());
126 BLECharacteristic *rx = uart->createCharacteristic(UART_RX, BLECharacteristic::PROPERTY_WRITE | BLECharacteristic::PROPERTY_WRITE_NR);
127 rx->setCallbacks(new RxEvents());
128 uart->start();
129 BLEAdvertisementData adv;
130 adv.setFlags(0x06);
131 adv.setCompleteServices(BLEUUID(UART_SERVICE));
132 BLEAdvertisementData scan;
133 scan.setName(BLE_NAME);
134 BLEAdvertising *advertising = BLEDevice::getAdvertising();
135 advertising->setAdvertisementData(adv);
136 advertising->setScanResponseData(scan);
137 BLEDevice::startAdvertising();
138}
139
140void btPoll() {
141 while (rxTail != rxHead) {
142 char c = (char)rxBuf[rxTail];
143 rxTail = (rxTail + 1) % RX_SIZE;
144 feed(c);
145 }
146 if (linkLost) {
147 linkLost = false;
148 onLinkLost();
149 delay(100);
150 BLEDevice::startAdvertising();
151 }
152}
153
154// ── ESP32 ──
155int speedLimit = 80; // speed limit from the app (0–100 %)
156unsigned long lastCommandMs = 0;
157bool moving = false;
158
159// if the car drives backwards, swap that motor's two wires
160void motor(int en, int a, int b, int power) {
161 power = constrain(power, -100, 100);
162 digitalWrite(a, power > 0 ? HIGH : LOW);
163 digitalWrite(b, power < 0 ? HIGH : LOW);
164 analogWrite(en, abs(power) * speedLimit * 255L / 10000);
165}
166
167void drive(int left, int right) {
168 motor(ENA, IN1, IN2, left);
169 motor(ENB, IN3, IN4, right);
170 moving = left != 0 || right != 0;
171 lastCommandMs = millis();
172}
173
174void onValue(const char *key, const char *value) {
175 if (is(key, "joy")) { // Joystick: y is forward/back, x turns; mixed into left and right wheel speeds
176 const char *comma = strchr(value, ',');
177 int x = atoi(value), y = comma ? atoi(comma + 1) : 0;
178 drive(constrain(y + x, -100, 100), constrain(y - x, -100, 100));
179 } else if (is(key, "yon")) {
180 if (is(value, "ileri")) drive(100, 100);
181 else if (is(value, "geri")) drive(-100, -100);
182 else if (is(value, "sol")) drive(-70, 70);
183 else if (is(value, "sag")) drive(70, -70);
184 else drive(0, 0);
185 } else if (is(key, "hiz")) {
186 speedLimit = constrain(atoi(value), 0, 100);
187 }
188}
189
190void sendAll() {
191 sendInt("hiz", speedLimit);
192}
193
194void onLinkLost() {
195 drive(0, 0); // Connection lost: the motors stop
196}
197
198void setup() {
199 Serial.begin(115200);
200 int pins[] = { ENA, IN1, IN2, ENB, IN3, IN4 };
201 for (int pin : pins) pinMode(pin, OUTPUT);
202 drive(0, 0);
203 btBegin();
204 Serial.print(F("BlueGrays Bluetooth: "));
205 Serial.println(BLE_NAME);
206}
207
208void loop() {
209 btPoll();
210 if (moving && millis() - lastCommandMs > COMMAND_TIMEOUT_MS) drive(0, 0);
211}
212Ko‘p so‘raladigan savollar
iPhone bilan ishlaydimi? HC-05 dan nimasi bilan farq qiladi?
Ha, iPhone va Android-da ishlaydi. HC-05 va HC-06 kabi klassik Bluetooth modullari iPhone-ga ulana olmaydi, shuning uchun bu loyiha ESP32-ning o‘rnatilgan Bluetooth Low Energy-sidan foydalanadi va qo‘shimcha modul talab qilmaydi. Platani telefoningning Bluetooth sozlamalarida bog‘lashga urinma; ulanishni faqat BlueGrays ilovasi o‘rnatadi.
Mashina orqaga yuryapti yoki bitta g‘ildirak teskari aylanyapti.
Noto‘g‘ri tomonga aylanayotgan motorning ikki simini L298N vintli klemmasida almashtir (chap motor OUT1/OUT2, o‘ng motor OUT3/OUT4); koddagi izoh ham shuni aytadi. Oldinga bosganda mashina joyida aylansa, faqat bitta motor teskari. Ikkalasi to‘g‘ri aylansa-yu, chapga burganda o‘ngga ketsa, chap va o‘ng motorlarni almashtir.
ESP32-ga quvvatni qanday beraman? USB va batareya bir vaqtda ulangan bo‘lishi mumkinmi?
2 ta 18650 batareya (7,4 V) L298N-ning 12V kirishiga ulanadi, L298N-ning 5V chiqishi esa ESP32-ning VIN piniga quvvat beradi; buning uchun L298N dagi 5V regulyator jumperi joyida qolishi kerak. Shunda mashina kabelsiz ishlaydi. Yuklash paytida USB ulangan bo‘lsa, ikki manba to‘qnashmasligi uchun batareyani o‘chir yoki 5V simini sug‘urib qo‘y. L298N GND va ESP32 GND har doim ulangan bo‘lishi shart.
Masofa qancha? Ulanish uzilsa, mashina nima qiladi?
Bluetooth Low Energy ochiq joyda odatda 10 dan 30 metrgacha yetadi; oradagi devorlar va odamlar bu masofani qisqartiradi. Ulanish uzilsa, plata motorlarni darhol to‘xtatadi va yana o‘zini e’lon qila boshlaydi (advertising), shuning uchun ilovadan qayta ulanishing mumkin. Plata 500 ms davomida buyruq olmasa ham mashina to‘xtaydi, shuning uchun u hech qachon masofadan tashqariga qochib ketmaydi.
