ESP32 va MQ-2 bilan gaz/tutun signalizatsiyasi
Bu loyihada MQ-2 gaz sensori moduli yordamida yonuvchi gaz (LPG, metan, propan) va tutun aniqlanadi va aniqlanganda passiv buzzer orqali sirenaga o‘xshash signal chalinadi. Sensorning raqamli chegara chiqishi (DO) ESP32-ning GPIO 4 piniga ulanadi; gaz yoki tutun chegaradan oshganda DO LOW bo‘ladi va signal ishga tushadi. Sezgirlik modul potensiometri bilan sozlanadi. Passiv buzzer ikki chastotali sirena effekti uchun tone() bilan boshqariladi.

Video
Elektr sxemasi

Manba kodi
1// ─────────────────────────────────────────
2// BlueGrays · bluegrays.com
3// ESP32 MQ-2 Gas/Smoke Detector Alarm
4// ─────────────────────────────────────────
5// Reads the digital threshold output (DO) of the MQ-2 module. When gas or
6// smoke passes the threshold, the warning LED turns on and the passive
7// buzzer plays a siren switching between 800 and 1200 Hz every 0.2 s. Set
8// the threshold with the trimpot on the module (Arduino Core 3.0+).
9//
10// Pins:
11// GPIO 4 -> MQ-2 DO (digital threshold output)
12// GPIO 18 -> Buzzer + leg
13// GPIO 5 -> Red LED (with a 220 ohm resistor)
14// MQ-2 VCC -> MQ-2 VCC -> 5V (VIN), GND -> GND
15
16// Pin definitions
17const int MQ2_DO_PIN = 4; // MQ-2 D0 (digital threshold out)
18const int BUZZER_PIN = 18; // Passive buzzer
19const int LED_PIN = 5; // Warning LED + 220R
20
21// Warm-up time (ms): the MQ-2 heater needs minutes to warm up. In Wokwi 2000 is enough.
22const unsigned long WARMUP_MS = 60000;
23bool warmedUp = false; // Is the warm-up over
24
25void setup() {
26 pinMode(MQ2_DO_PIN, INPUT);
27 pinMode(BUZZER_PIN, OUTPUT);
28 pinMode(LED_PIN, OUTPUT);
29 digitalWrite(BUZZER_PIN, LOW);
30 digitalWrite(LED_PIN, LOW);
31}
32
33void loop() {
34 // Warm-up: the DO reading is ignored, the LED blinks slowly without blocking
35 if (!warmedUp) {
36 if (millis() < WARMUP_MS) {
37 digitalWrite(LED_PIN, (millis() / 500) % 2); // 0.5 s on, 0.5 s off
38 return;
39 }
40 warmedUp = true;
41 }
42
43 // MQ-2 D0 is normally HIGH and goes LOW above the threshold
44 int gasState = digitalRead(MQ2_DO_PIN);
45
46 if (gasState == LOW) {
47 // Alarm: the LED turns on, the buzzer plays a two-tone siren
48 digitalWrite(LED_PIN, HIGH);
49 tone(BUZZER_PIN, 800); // Low tone
50 delay(200);
51 tone(BUZZER_PIN, 1200); // High tone
52 delay(200);
53 } else {
54 // Idle: LED and buzzer off
55 digitalWrite(LED_PIN, LOW);
56 noTone(BUZZER_PIN);
57 delay(50);
58 }
59}
60
Ko‘p so‘raladigan savollar
MQ-2 qaysi gazlarni aniqlaydi?
MQ-2 LPG, propan, metan, vodorod, spirt bug‘i va tutunga sezgir. U gazlarni bir-biridan ajrata olmaydi; faqat umumiy konsentratsiya oshganini aniqlaydi.
MQ-2 ning analog chiqishini ESP32-ga to‘g‘ridan-to‘g‘ri ulasa bo‘ladimi?
MQ-2 5 V dan quvvatlanadi va uning analog chiqishi 5 V gacha yetishi mumkin. ESP32-ning ADC kirishi ko‘pi bilan 3,3 V qabul qilgani uchun kuchlanish bo‘lgich (masalan, 10 kΩ + 20 kΩ) ishlatish shart.
Sensor birinchi yoqilganda yuqori qiymat ko‘rsatadi. Nega?
MQ sensorlarining qizdirgichi barqarorlashishi uchun bir necha daqiqa kerak; bu vaqtda o‘qishlar yuqori bo‘ladi. Ishga tushgandan keyin signalni bir necha daqiqa o‘chirib qo‘yish soxta signallarning oldini oladi.
Sirena effekti qanday hosil qilinadi?
Passiv buzzer `tone()` yordamida ikki xil chastota (masalan, 800 Hz va 1200 Hz) orasida tez almashib turadigan qilib boshqariladi. Bu almashinish klassik signal ovozini taqlid qiladi.
