Raspberry Pi Pico: 4 rejimli tugma bilan svetofor (holat mashinasi)
Bitta tugma bilan svetoforning 4 ta rejimi! Har bosishda rejim almashadi: oddiy sikl (qizil → sariq → yashil), faqat qizil (to‘xta), miltillovchi sariq (ehtiyot/tungi rejim) va o‘chiq (ta’mirlash). Holat mashinasini (qaysi xatti-harakat ishlashini mode o‘zgaruvchisi hal qiladi) va (mode + 1) % 4 bilan rejimlar bo‘ylab aylanishni o‘rganasan.

Video
Elektr sxemasi

Manba kodi
1# ─────────────────────────────────────────
2# BlueGrays · bluegrays.com
3# Raspberry Pi Pico Traffic Light with 4-Mode Button Selector (State Machine, GP11-13 + GP4)
4# ─────────────────────────────────────────
5# One button cycles 4 modes: normal cycle (red -> yellow -> green), red
6# only, yellow flash and off. Uses a state machine and non-blocking timing
7# with time.ticks_ms(), so the button is always responsive.
8#
9# Pins:
10# GP11 -> Green LED
11# GP12 -> Yellow LED
12# GP13 -> Red LED (each LED with 220 ohm)
13# GP4 -> Button (other leg to GND)
14
15from machine import Pin
16import time
17
18# ============ LEDS ============
19green = Pin(11, Pin.OUT) # Green
20yellow = Pin(12, Pin.OUT) # Yellow
21red = Pin(13, Pin.OUT) # Red
22
23# ============ BUTTON ============
24button = Pin(4, Pin.IN, Pin.PULL_UP) # Reads 0 when pressed
25
26# ============ STATE ============
27# Mode: 0 normal cycle, 1 red only, 2 yellow flash, 3 off
28mode = 0
29last_btn = 1 # Previous button value
30blink_state = False # Yellow flash state
31last_tick = time.ticks_ms() # Last flash toggle
32
33# ============ NORMAL CYCLE ============
34normal_step = 0 # 0: red, 1: yellow, 2: green
35normal_last = time.ticks_ms() # Step start time
36NORMAL_TIMES = [3000, 1000, 3000] # Red, Yellow, Green (ms)
37LEDS = [red, yellow, green]
38
39def all_off():
40 # Turn all LEDs off
41 red.off(); yellow.off(); green.off()
42
43# ============ MAIN LOOP ============
44while True:
45 btn = button.value()
46
47 # ---- Button pressed (1 -> 0): mode change ----
48 if last_btn == 1 and btn == 0:
49 mode = (mode + 1) % 4
50 all_off()
51 normal_step = 0
52 normal_last = time.ticks_ms()
53 time.sleep_ms(200) # Debounce
54 last_btn = btn
55
56 now = time.ticks_ms()
57
58 # ---- Normal traffic light cycle ----
59 if mode == 0:
60 if time.ticks_diff(now, normal_last) > NORMAL_TIMES[normal_step]:
61 normal_step = (normal_step + 1) % 3
62 normal_last = now
63 all_off()
64 LEDS[normal_step].on()
65
66 # ---- Red only (stop) ----
67 elif mode == 1:
68 all_off(); red.on()
69
70 # ---- Yellow flash, 0.4 s (caution/night) ----
71 elif mode == 2:
72 if time.ticks_diff(now, last_tick) > 400:
73 blink_state = not blink_state
74 yellow.value(blink_state)
75 last_tick = now
76 red.off(); green.off()
77
78 # ---- Off ----
79 else:
80 all_off()
81
82 time.sleep_ms(10)
83Ko‘p so‘raladigan savollar
Holat mashinasi (state machine) nima?
Dastur ayni paytda nima qilayotganini bitta o‘zgaruvchi (mode) hal qiladi. Har bosishda mode o‘zgaradi, sikl esa faqat joriy rejimga tegishli kodni bajaradi. Bu murakkab xatti-harakatlarni tartibli saqlashning standart usuli.
(mode + 1) % 4 nima qiladi?
U rejimni bittaga oshiradi va 4 ga yetganda 0 ga qaytaradi, shunday qilib rejim 0, 1, 2, 3, 0, 1... tarzida cheksiz aylanadi.
Nega time.sleep() o‘rniga ticks_ms() ishlatiladi?
sleep() paytida Pico tugmani o‘qiy olmaydi, shuning uchun rejim o‘zgarishi kechikadi. ticks_ms() va ticks_diff() LED bosqichlari davomida uzoq kutishning oldini oladi. Lekin bu versiyada rejim o‘zgarganda debounce uchun 200 ms va har sikl oxirida 10 ms kutish bor; bu oraliqlarda tugma qayta o‘qilmaydi.
Yangi rejim qo‘sha olamanmi?
Ha, rejimlar sonini 5 ga oshirib, yangi rejim uchun alohida xatti-harakat blokini yoz, masalan, yashil miltillash yoki barcha chiroqlarni navbat bilan yoqish.
