Raspberry Pi Pico parkovka sensori (HC-SR04 + 3 ta LED + buzzer)
Mashinangdagi orqa parkovka sensorini stoling ustiga olib kel! Raspberry Pi Pico HC-SR04 ultratovushli sensori bilan to‘siqqacha masofani soniyasiga taxminan 16 marta o‘lchaydi. Yaqinlashgan sari yashil, sariq va qizil LED-lar navbat bilan yonadi va buzzer tezroq chiyillaydi; 10 sm dan kamda ovoz uzluksiz bo‘ladi va qizil LED miltillaydi. Ultratovushli masofa o‘lchash, PWM ovoz va bloklamaydigan vaqt hisobi bitta loyihada.

Video
Elektr sxemasi

Manba kodi
1# ─────────────────────────────────────────
2# BlueGrays · bluegrays.com
3# Raspberry Pi Pico Parking Sensor (HC-SR04 + 3 LEDs + Buzzer)
4# ─────────────────────────────────────────
5# Car parking sensor. The HC-SR04 measures the distance to an obstacle; as
6# it gets closer the green, yellow and red LEDs light up in turn and the
7# beeps speed up. Very close, the tone becomes continuous and the red LED
8# flashes.
9#
10# Pins:
11# GP27 -> HC-SR04 TRIG
12# GP26 -> HC-SR04 ECHO (1k + 2k divider on real hardware)
13# VBUS -> HC-SR04 VCC (5V), GND.6 -> HC-SR04 GND
14# GP4 -> 220 ohm -> Red LED (cathode to GND)
15# GP8 -> 220 ohm -> Yellow LED (cathode to GND)
16# GP12 -> 220 ohm -> Green LED (cathode to GND)
17# GP17 -> Buzzer (+), other leg to GND
18
19from machine import Pin, PWM, time_pulse_us
20import time
21
22# ============ SETTINGS ============
23GREEN_CM = 100 # Green on, beeping starts
24YELLOW_CM = 50 # Yellow joins in
25RED_CM = 25 # Red joins in
26STOP_CM = 10 # Continuous tone + flashing red
27
28BEEP_MS = 60 # Length of one beep
29SLOW_GAP_MS = 700 # Gap between beeps at GREEN_CM
30FAST_GAP_MS = 50 # Gap between beeps near STOP_CM
31VOLUME = 32768 # PWM duty, 32768 = 50%
32FLASH_MS = 120 # Red flash period in STOP zone
33
34MEASURE_MS = 60 # Measure interval, min 60 ms
35PRINT_MS = 250 # Serial print interval
36ECHO_TIMEOUT_US = 12000 # beyond ~2 m = no obstacle
37SOUND_CM_PER_US = 0.0343 # Speed of sound (20 C)
38LOOP_MS = 5 # Main loop step
39
40# Zones from near to far: (name, upper limit cm, (green, yellow, red), tone Hz)
41ZONES = (
42 ("STOP", STOP_CM, (1, 1, 1), 1900),
43 ("RED", RED_CM, (1, 1, 1), 1900),
44 ("YELLOW", YELLOW_CM, (1, 1, 0), 1500),
45 ("GREEN", GREEN_CM, (1, 0, 0), 1200),
46)
47CLEAR = len(ZONES) # No obstacle zone
48STOP = 0 # Index of the STOP zone
49
50# ============ HARDWARE ============
51trig = Pin(27, Pin.OUT, value=0)
52echo = Pin(26, Pin.IN)
53led_green = Pin(12, Pin.OUT, value=0)
54led_yellow = Pin(8, Pin.OUT, value=0)
55led_red = Pin(4, Pin.OUT, value=0)
56buzzer = PWM(Pin(17))
57buzzer.duty_u16(0)
58
59
60# ============ MEASUREMENT ============
61def measure_cm():
62 # Send a 10 us TRIG pulse, time how long ECHO stays HIGH
63 trig.value(0)
64 time.sleep_us(2)
65 trig.value(1)
66 time.sleep_us(10)
67 trig.value(0)
68 pulse = time_pulse_us(echo, 1, ECHO_TIMEOUT_US)
69 if pulse < 0:
70 return None # No echo or too far
71 # Sound travels there and back: half
72 return pulse * SOUND_CM_PER_US / 2
73
74
75def median3(values):
76 # Median of the last 3 readings: one bad reading does not flicker the LEDs
77 a, b, c = values
78 return max(min(a, b), min(max(a, b), c))
79
80
81def zone_of(dist):
82 if dist is None:
83 return CLEAR
84 for i, zone in enumerate(ZONES):
85 if dist <= zone[1]:
86 return i
87 return CLEAR
88
89
90def beep_gap_ms(dist):
91 # Between STOP_CM and GREEN_CM the beep gap grows linearly from FAST to SLOW
92 ratio = (dist - STOP_CM) / (GREEN_CM - STOP_CM)
93 ratio = min(1.0, max(0.0, ratio))
94 return int(FAST_GAP_MS + ratio * (SLOW_GAP_MS - FAST_GAP_MS))
95
96
97# ============ SOUND ============
98tone_on = False
99tone_hz = 0
100
101
102def tone(hz):
103 # Leave PWM alone if the tone is already on
104 global tone_on, tone_hz
105 if tone_on and tone_hz == hz:
106 return
107 buzzer.freq(hz)
108 buzzer.duty_u16(VOLUME)
109 tone_on = True
110 tone_hz = hz
111
112
113def silence():
114 global tone_on
115 if tone_on:
116 buzzer.duty_u16(0)
117 tone_on = False
118
119
120def set_leds(green, yellow, red):
121 led_green.value(green)
122 led_yellow.value(yellow)
123 led_red.value(red)
124
125
126def self_test():
127 # Short power-on test of LEDs and buzzer: green -> yellow -> red
128 for leds, hz in (((1, 0, 0), 1200), ((1, 1, 0), 1500), ((1, 1, 1), 1900)):
129 set_leds(*leds)
130 tone(hz)
131 time.sleep_ms(90)
132 silence()
133 time.sleep_ms(160)
134 set_leds(0, 0, 0)
135
136
137# ============ MAIN LOOP ============
138print("== BlueGrays · bluegrays.com ==")
139print("Parking Sensor")
140print("LEDs: green <= %d cm, yellow <= %d cm, red <= %d cm, continuous tone <= %d cm"
141 % (GREEN_CM, YELLOW_CM, RED_CM, STOP_CM))
142print("Beep: starts at %d cm, higher pitch at %d cm and %d cm, continuous at %d cm"
143 % (GREEN_CM, YELLOW_CM, RED_CM, STOP_CM))
144self_test()
145
146FAR = 999.0 # Placeholder for no obstacle
147history = [FAR, FAR, FAR] # Last 3 readings
148distance = None # Filtered distance (cm)
149zone = CLEAR
150last_zone = -1
151now = time.ticks_ms()
152next_measure = now
153next_print = now
154last_beep = time.ticks_add(now, -10000) # First beep plays at once
155beep_end = now
156
157while True:
158 now = time.ticks_ms()
159
160 # 1) Measurement: every MEASURE_MS, with a median filter
161 if time.ticks_diff(now, next_measure) >= 0:
162 next_measure = time.ticks_add(now, MEASURE_MS)
163 reading = measure_cm()
164 history = history[1:] + [reading if reading is not None else FAR]
165 filtered = median3(history)
166 distance = None if filtered >= FAR else filtered
167 zone = zone_of(distance)
168 if zone != last_zone:
169 name = "CLEAR" if zone == CLEAR else ZONES[zone][0]
170 print("Zone ->", name)
171 last_zone = zone
172
173 # 2) LEDs: bar graph, red flashes in the STOP zone
174 if zone == CLEAR:
175 set_leds(0, 0, 0)
176 elif zone == STOP:
177 flash_on = (now // FLASH_MS) % 2 == 0
178 set_leds(1, 1, 1 if flash_on else 0)
179 else:
180 set_leds(*ZONES[zone][2])
181
182 # 3) Sound: non-blocking beep timer
183 if zone == CLEAR:
184 silence()
185 elif zone == STOP:
186 tone(ZONES[STOP][3]) # Very close: continuous tone
187 else:
188 if tone_on and time.ticks_diff(now, beep_end) >= 0:
189 silence()
190 # The gap is recalculated every pass: the next beep speeds up as soon as you get closer
191 period = BEEP_MS + beep_gap_ms(distance)
192 if not tone_on and time.ticks_diff(now, last_beep) >= period:
193 tone(ZONES[zone][3])
194 last_beep = now
195 beep_end = time.ticks_add(now, BEEP_MS)
196
197 # 4) Serial monitor: distance in cm
198 if time.ticks_diff(now, next_print) >= 0:
199 next_print = time.ticks_add(now, PRINT_MS)
200 if distance is None:
201 print("Distance: --- (no obstacle)")
202 else:
203 print("Distance: %5.1f cm" % distance)
204
205 time.sleep_ms(LOOP_MS)
206Ko‘p so‘raladigan savollar
Nega haqiqiy sxemada ECHO ga kuchlanish bo‘lgich kerak?
HC-SR04 5V da ishlaydi va uning ECHO chiqishi 5V, Pico pinlari esa ko‘pi bilan 3,3V qabul qiladi. ECHO ni GP26 ga 1 kΩ orqali, GP26 ni esa GND-ga 2 kΩ orqali ula, shunda pin taxminan 3,3V ko‘radi. Wokwi-da bo‘lgich kerak emas.
Ogohlantirish masofalarini qanday o‘zgartiraman?
Kod boshidagi `GREEN_CM`, `YELLOW_CM`, `RED_CM` va `STOP_CM` konstantalarini tahrirla. Chegaralarni `STOP_CM < RED_CM < YELLOW_CM < GREEN_CM` tartibida saqla; masalan, `STOP_CM = 30`, `RED_CM = 50`, `YELLOW_CM = 100` va `GREEN_CM = 150` qil. LED-lar va signallar yangi chegaralarga avtomatik moslashadi.
Nega signallar zonama-zona emas, silliq tezlashadi?
`beep_gap_ms()` oraliqni masofaga qarab chiziqli o‘zgartiradi: 100 sm da 700 ms, 10 sm da 50 ms. U asosiy siklning har aylanishida qayta hisoblanadi, shuning uchun to‘siq yaqinlashgan zahoti keyingi signal ertaroq keladi. Zonalar faqat LED-lar va ohang balandligini o‘zgartiradi.
Biror kutubxona o‘rnatishim kerakmi?
Yo‘q. O‘lchashda ishlatiladigan `time_pulse_us()` funksiyasi o‘rnatilgan `machine` modulining bir qismi. Pico-ga MicroPython yozib, kodni Thonny-da unga `main.py` nomi bilan saqla; sensor LED sinovi va uchta signal bilan o‘zi ishga tushadi.
