DHT22
Komponen

DHT22

4.5(10)
18
The DHT22 is a digital sensor module for temperature and humidity measurement. It offers a much wider measurement range and higher accuracy compared to the DHT11 from the same family. It can measure temperature between -40°C and +80°C with ±0.5°C accuracy and humidity between 0% and 100% with ±2-5% accuracy. It easily communicates with Arduino and ESP series boards via a single data pin. It is preferred instead of DHT11 in applications such as precise environmental monitoring, weather station and greenhouse automation.

Projek yang menggunakan komponen ini

Dot Matrix Clock, Calendar and Weather Station (MAX7219, DS1307)
AR-85Pertengahan
Premium

Dot Matrix Clock, Calendar and Weather Station (MAX7219, DS1307)

A scrolling-text board for your desk or wall that shows the time, the date and the room's weather in turn.

5.0(50)
66
ESP32 DHT22 Temperature and Humidity (with LCD Display)
ES-15Pertengahan

ESP32 DHT22 Temperature and Humidity (with LCD Display)

This project measures ambient temperature and humidity using a DHT22 sensor and displays the data in real time on a 16x2 I2C LCD. Data is read from the sensor using the one-wire protocol via the Adafruit DHT library. This project serves as the foundation for IoT weather stations, smart home automation, or environmental monitoring systems in greenhouses. Communication with the DHT22 is established via the ESP32's GPIO 4 pin.

4.8(38)
57
ESP32 Temperature Data Logger (DHT22 + DS1307 RTC + microSD + OLED)
ES-40Mahir
Premium

ESP32 Temperature Data Logger (DHT22 + DS1307 RTC + microSD + OLED)

Build a timed temperature and humidity logger with the ESP32! A DHT22 sensor reads temperature and humidity once a minute, and each reading is saved to a microSD card in CSV format with a real-time stamp from the DS1307 RTC module. The OLED display shows the latest temperature, humidity, timestamp and total number of records live, in large text.

4.7(7)
12
Raspberry Pi Pico Mini Weather Station (DHT22 + OLED Chart)
PI-21Pertengahan
Premium

Raspberry Pi Pico Mini Weather Station (DHT22 + OLED Chart)

How has your room's temperature changed over the last two minutes? The Raspberry Pi Pico reads temperature and humidity from a DHT22 every 2 seconds and shows the value in big digits on a 0.96 inch OLED, with a line chart of the last 60 readings below. An arrow shows the trend and the temperature and humidity pages swap every 4 seconds. The OLED driver is built into the code: one file, no libraries.

Arduino Smart Thermostat (DHT22 + Relay + I2C LCD)
AR-107Pertengahan
Premium

Arduino Smart Thermostat (DHT22 + Relay + I2C LCD)

Room at 19 degrees, target 21: the relay clicks on! The DHT22 measures the temperature, and when it drops below the target the relay turns the heater on. Thanks to hysteresis, the relay does not keep clicking around the target. Two buttons set the target in 0.5 °C steps, and it is kept in EEPROM; the I2C LCD shows temperature, humidity and heater state. The basics of real home automation in one project.

5.0(1)
1
ESP32 microSD Temperature and Humidity Logger (DHT22 + ILI9341 Graph)
ES-52Pertengahan
Premium

ESP32 microSD Temperature and Humidity Logger (DHT22 + ILI9341 Graph)

Log the temperature of a room, greenhouse or fridge all day long! An ESP32 measures temperature and humidity with a DHT22 every 2 s and writes each reading to a CSV file on a microSD card. The ILI9341 color display shows live values, min and max, and a two-color live graph of the last 30 readings. Plug the card into your computer and open the file in Excel.

ESP32 Egg Incubator Controller (DHT22 + Relay + Servo + OLED)
ES-54Pertengahan
Premium

ESP32 Egg Incubator Controller (DHT22 + Relay + Servo + OLED)

Hand the hen's job to an ESP32! The DHT22 measures temperature and humidity, a relay switches the heater with hysteresis, an SG90 servo gently tilts the egg tray every 3 hours, and the 0.96 inch OLED shows the day counter, a temperature graph and alarms. Chicken, quail and duck profiles are built in, and turning stops by itself for the last 3 days. If the sensor fails, the heater switches off for safety.

Arduino 5-Minute Shower: A Clock That Starts Itself with Steam (DHT22 + TM1637 + Buzzer)
AR-146Pemula
Premium

Arduino 5-Minute Shower: A Clock That Starts Itself with Steam (DHT22 + TM1637 + Buzzer)

End the "who has been in the shower for 20 minutes?" fight at home: a DHT22 notices the humidity rising with the steam and the clock starts by itself, nobody has to press a button. A TM1637 display shows minutes:seconds, and a green, yellow and red LED tell the time by colour. The buzzer sounds at minute 5, then gives a short reminder every minute. When the humidity drops, the timer stops and the final time stays on the display.

ESP32 Frost Alarm: Will the Windshield Freeze Tomorrow Morning? (DHT22 + I2C LCD + 2 LEDs + Buzzer)
ES-88Pemula
Premium

ESP32 Frost Alarm: Will the Windshield Freeze Tomorrow Morning? (DHT22 + I2C LCD + 2 LEDs + Buzzer)

No more scraping the car window at 7 am: the DHT22 measures outdoor temperature and humidity, the ESP32 works out the dew point and tells you whether the windshield will freeze tonight. The I2C LCD shows temperature, humidity and dew point; green LED means SAFE, blinking red RISK, steady red plus a buzzer alarm FROST. If the air cooled fast in the last hour, it warns you about the night too.

ESP32 IoT Room Station (Relay + DHT22)
ES-99Pertengahan
IoT

ESP32 IoT Room Station (Relay + DHT22)

Turn your lamp on from your phone and watch your room's temperature and humidity live, wherever you are. This project is the step-by-step guide to the Room station IoT template in the app, built with an ESP32, a relay module and a DHT22. Go to Workshop › Devices › Add a device and pick Room station; Ohmi prepares the code with your own device key. The code on this page is an example: the key and Wi-Fi details are placeholders.

5.0(1)
4
Pico W IoT Temperature and Humidity (DHT22)
PI-96Pemula
IoT

Pico W IoT Temperature and Humidity (DHT22)

Watch your room's temperature and humidity live on your phone wherever you are. This project is the step-by-step guide to the Temperature and humidity IoT template in the app, built with a Raspberry Pi Pico W and a DHT22. Go to Workshop › Devices › Add a device, pick Pico W as the board and Temperature and humidity as the template; Ohmi prepares the code with your own device key. The code on this page is an example: the key and Wi-Fi details are placeholders.

1