Loyihalar · Arduino / ESP32 / Pico

Arduino loyihalarini kashf qil

Boshlang‘ichdan yuqori darajagacha, sxemali, kodli va videoli yuzlab loyihalar. Qaysi darajada bo‘lsang, o‘sha yerdan boshla.

Reading a Reed Switch
AR-37Boshlang‘ich

Reading a Reed Switch

Ever wondered about the magnetic switch inside door and window alarms? When a magnet comes near the reed relay module, the tiny switch inside it closes; the Arduino reads it once a second and prints…

4.5(22)
29
3x4 Keypad Operation
AR-61Boshlang‘ich

3x4 Keypad Operation

The Arduino instantly knows which key you press on a 12-key keypad that looks like a phone dial pad, and writes it on your computer screen.

4.5(24)
32
ESP32 IoT Lamp Switch (Relay)
ES-100Boshlang‘ich
IoT

ESP32 IoT Lamp Switch (Relay)

Turn your lamp on and off from your phone, wherever you are. This project is the step-by-step guide to the Relay lamp IoT template in the app, built with an ESP32 and a relay module and tried with an LED first. Go to Workshop › Devices › Add a device and pick Relay lamp; Ohmi prepares the code with your own device key. The code on this page is an example: the key and Wi-Fi details are placeholders.

Pico W IoT Temperature and Humidity (DHT22)
PI-96Boshlang‘ich
IoT

Pico W IoT Temperature and Humidity (DHT22)

Watch your room's temperature and humidity live on your phone wherever you are. This project is the step-by-step guide to the Temperature and humidity IoT template in the app, built with a Raspberry Pi Pico W and a DHT22. Go to Workshop › Devices › Add a device, pick Pico W as the board and Temperature and humidity as the template; Ohmi prepares the code with your own device key. The code on this page is an example: the key and Wi-Fi details are placeholders.

1
Pico W IoT Door Sensor (Reed Switch)
PI-97Boshlang‘ich
IoT

Pico W IoT Door Sensor (Reed Switch)

Did you leave the door or window open? Check on your phone wherever you are. This project is the step-by-step guide to the Door / window IoT template in the app, built with a Raspberry Pi Pico W, a reed switch and a small magnet using two wires. Go to Workshop › Devices › Add a device, pick Pico W as the board and Door / window as the template; Ohmi prepares the code with your own device key. The code on this page is an example: the key and Wi-Fi details are placeholders.

1
Pico W IoT Motion Counter (PIR)
PI-98Boshlang‘ich
IoT

Pico W IoT Motion Counter (PIR)

Count how many times someone walks through a door or hallway, and see the moment of motion live on your phone. This project is the step-by-step guide to the Motion detector IoT template in the app, built with a Raspberry Pi Pico W and a PIR motion sensor using just 3 wires. Go to Workshop › Devices › Add a device; Ohmi prepares the code with your own device key. The code on this page is an example: the key and Wi-Fi details are placeholders.

ESP32 Bluetooth LED and Relay
ES-108Boshlang‘ich
Bluetooth

ESP32 Bluetooth LED and Relay

Switch an LED and a relay on and off from your phone over Bluetooth, no internet or Wi-Fi needed. This project is the step-by-step guide to the LED and relay Bluetooth template in the app, built with an ESP32 and a 5 V relay module. Go to Workshop › Devices › Add a device › Bluetooth, pick LED and relay and upload the code with Get the code. The Set up as a Bluetooth panel button on this page opens the wizard with this template too.

ESP32 Bluetooth Temp and Humidity (DHT11)
ES-109Boshlang‘ich
Bluetooth

ESP32 Bluetooth Temp and Humidity (DHT11)

Watch your room's temperature and humidity live on your phone with an ESP32 and a DHT11 sensor: two reading boxes and a chart update every 2 seconds, no internet needed. This project is the step-by-step guide for the Temperature and humidity Bluetooth template in the app. Go to Workshop › Devices › Add a device › Bluetooth, pick the template and upload the code with Get the code. The Set up as a Bluetooth panel button on this page opens the wizard ready to go.

ESP32 Bluetooth Servo Lock
ES-111Boshlang‘ich
Bluetooth

ESP32 Bluetooth Servo Lock

Control an SG90 servo as a small latch from your phone over Bluetooth: lock, open or set the angle, no internet or Wi-Fi needed. This project is the step-by-step guide to the Servo lock Bluetooth template in the app, built with an ESP32, one servo and 3 wires. Go to Workshop › Devices › Add a device › Bluetooth, pick Servo lock and upload the code with Get the code. The Set up as a Bluetooth panel button on this page opens the wizard with this template too.

ESP32 Bluetooth Text on an LCD
ES-112Boshlang‘ich
Bluetooth

ESP32 Bluetooth Text on an LCD

Type a message on your phone and it shows up on a 16x2 LCD over Bluetooth, no internet or Wi-Fi needed. This project is the step-by-step guide to the Text on an LCD Bluetooth template in the app, built with an ESP32 and an I2C LCD. Go to Workshop › Devices › Add a device › Bluetooth, pick Text on an LCD and upload the code with Get the code. The Set up as a Bluetooth panel button on this page opens the wizard with this template too.