Loyihalar · Arduino / ESP32 / Pico

Arduino loyihalarini kashf qil

Boshlang‘ichdan yuqori darajagacha, sxemali, kodli va videoli yuzlab loyihalar. Qaysi darajada bo‘lsang, o‘sha yerdan boshla.

Measuring Light Intensity with an LDR
AR-11Boshlang‘ich

Measuring Light Intensity with an LDR

Want to see how bright your room is as a number? The LDR, a small part that reacts to light, measures the light around it, and the Arduino writes the value to your computer screen every half second.

4.6(83)
143
Night Light with Ldr
AR-12Boshlang‘ich

Night Light with Ldr

A little night light that turns on by itself when it gets dark and goes off when morning comes.

4.7(105)
225
HC-SR04 Distance Measurement (Serial Display)
AR-27Boshlang‘ich

HC-SR04 Distance Measurement (Serial Display)

The HC-SR04 sensor works just like a bat finding its way in the dark: it sends out a sound you cannot hear, listens for the echo and measures how far away the object in front of it is.

4.6(50)
82
Reading a Reed Switch
AR-37Boshlang‘ich

Reading a Reed Switch

Ever wondered about the magnetic switch inside door and window alarms? When a magnet comes near the reed relay module, the tiny switch inside it closes; the Arduino reads it once a second and prints…

4.5(22)
29
Reading Light Intensity with the ESP32 LDR Module
ES-11Boshlang‘ich

Reading Light Intensity with the ESP32 LDR Module

Real-time monitoring of the LDR module's raw ADC value and relative light percentage calculated from dark and light reference values in the Serial Monitor. This percentage is not a lux measurement. Teaches the module’s calibration logic. It is ideal to complete this before Project 10, as it is used to determine the threshold value.

4.6(36)
55
Raspberry Pi Pico Parking Sensor (HC-SR04 + 3 LEDs + Buzzer)
PI-18Boshlang‘ich

Raspberry Pi Pico Parking Sensor (HC-SR04 + 3 LEDs + Buzzer)

Bring your car's reverse parking sensor to your desk! The Raspberry Pi Pico uses an HC-SR04 ultrasonic sensor to measure the distance to an obstacle about 16 times a second. As it gets closer, the green, yellow and red LEDs light up in turn and the buzzer beeps faster; under 10 cm the tone turns continuous and the red LED flashes. Ultrasonic ranging, PWM sound and non-blocking timing in one project.

1
Pico W IoT Temperature and Humidity (DHT22)
PI-96Boshlang‘ich
IoT

Pico W IoT Temperature and Humidity (DHT22)

Watch your room's temperature and humidity live on your phone wherever you are. This project is the step-by-step guide to the Temperature and humidity IoT template in the app, built with a Raspberry Pi Pico W and a DHT22. Go to Workshop › Devices › Add a device, pick Pico W as the board and Temperature and humidity as the template; Ohmi prepares the code with your own device key. The code on this page is an example: the key and Wi-Fi details are placeholders.

1
ESP32 Bluetooth Temp and Humidity (DHT11)
ES-109Boshlang‘ich
Bluetooth

ESP32 Bluetooth Temp and Humidity (DHT11)

Watch your room's temperature and humidity live on your phone with an ESP32 and a DHT11 sensor: two reading boxes and a chart update every 2 seconds, no internet needed. This project is the step-by-step guide for the Temperature and humidity Bluetooth template in the app. Go to Workshop › Devices › Add a device › Bluetooth, pick the template and upload the code with Get the code. The Set up as a Bluetooth panel button on this page opens the wizard ready to go.

ESP32 Bluetooth Parking Sensor (HC-SR04)
ES-113Boshlang‘ich
Bluetooth

ESP32 Bluetooth Parking Sensor (HC-SR04)

Measure the distance to an obstacle with an HC-SR04 and watch it on your phone; the buzzer beeps faster as it gets closer. No internet needed. This is the step-by-step guide to the Parking sensor Bluetooth template in the app, built with an ESP32. Go to Workshop › Devices › Add a device › Bluetooth, pick Parking sensor and upload the code with Get the code. The Set up as a Bluetooth panel button on this page opens the wizard with this template too.