Arduino loyihalarini kashf qil
Boshlang‘ichdan yuqori darajagacha, sxemali, kodli va videoli yuzlab loyihalar. Qaysi darajada bo‘lsang, o‘sha yerdan boshla.

ESP32 Night Light with LDR
Night light where the LED automatically turns on in the dark and off in the light. The D0 (digital out) pin of the LDR Sensor Module is used - the dark threshold is set with the small potentiometer on the module, the module itself generates the HIGH/LOW output. ESP32 just reads this signal with digitalRead(), the code is very simple.

Reading Light Intensity with the ESP32 LDR Module
Real-time monitoring of the LDR module's raw ADC value and relative light percentage calculated from dark and light reference values in the Serial Monitor. This percentage is not a lux measurement. Teaches the module’s calibration logic. It is ideal to complete this before Project 10, as it is used to determine the threshold value.

ESP32 HC-SR04 Ultrasonic Distance Sensor
The HC-SR04 ultrasonic sensor measures distance by timing how long its sound pulse takes to bounce off an object and return (time of flight). In this project the ESP32 sends a 10-microsecond pulse to the TRIG pin and reads the echo time from the ECHO pin with pulseIn(). The distance is shown in cm on a 16x2 I2C LCD. The HC-SR04 runs on 5V, so the ECHO pin needs a voltage divider, or the ESP32's 3.3V GPIO gets damaged.

ESP32 DHT22 Temperature and Humidity (with LCD Display)
This project measures ambient temperature and humidity using a DHT22 sensor and displays the data in real time on a 16x2 I2C LCD. Data is read from the sensor using the one-wire protocol via the Adafruit DHT library. This project serves as the foundation for IoT weather stations, smart home automation, or environmental monitoring systems in greenhouses. Communication with the DHT22 is established via the ESP32's GPIO 4 pin.

ESP32 MQ-2 Gas/Smoke Detector Alarm
In this project, combustible gas (LPG, methane, propane) and smoke detection is performed using an MQ-2 gas sensor module, and a siren-like alarm is played through a passive buzzer upon detection. The sensor's digital threshold output (DO) is connected to GPIO 4 on the ESP32; when gas or smoke exceeds the threshold, DO goes LOW and the alarm is triggered. Sensitivity is adjusted via the module's potentiometer. The passive buzzer is driven using tone() to produce a two-frequency siren effect.

ESP32 Prayer Rakat Counter (HC-SR04 + SSD1306 OLED + 2 Buttons)
Do you sometimes lose track of which rakat you are on during prayer? This project is a rakat counter that sits next to your prayer mat and counts your prostrations when you bring your hand close. The HC-SR04 ultrasonic distance sensor detects your hand, the SSD1306 OLED display shows the count, and two buttons let you choose 2, 3 or 4 rakats and reset. A 2.5-second debounce and a "hand-away" check make sure no prostration is counted twice.

ESP32 Parking Sensor (HC-SR04 + 5-LED Bar + Buzzer + OLED)
The ESP32 version of a car parking sensor! The HC-SR04 ultrasonic sensor measures the distance to the object in front. As it gets closer, a 5-LED bar fills up (green → yellow → red) and the buzzer beeps faster. Very close (under 10 cm), a continuous alarm sounds and all LEDs light up. The SSD1306 OLED display shows the live distance in cm in large text, plus a status message.

ESP32 Temperature Data Logger (DHT22 + DS1307 RTC + microSD + OLED)
Build a timed temperature and humidity logger with the ESP32! A DHT22 sensor reads temperature and humidity once a minute, and each reading is saved to a microSD card in CSV format with a real-time stamp from the DS1307 RTC module. The OLED display shows the latest temperature, humidity, timestamp and total number of records live, in large text.

ESP32 Earthquake Shake Alarm (MPU-6050 + OLED Display + Buzzer)
When your desk shakes, this screen notices first! The ESP32 measures vibration with an MPU-6050 accelerometer and draws a live trace that scrolls like a seismograph on a 0.96-inch OLED display. When the shaking passes the threshold, a passive buzzer sounds a siren and the red LED flashes; one button silences and resets it. It is an educational shake meter, not an official earthquake warning.

ESP32 microSD Temperature and Humidity Logger (DHT22 + ILI9341 Graph)
Log the temperature of a room, greenhouse or fridge all day long! An ESP32 measures temperature and humidity with a DHT22 every 2 s and writes each reading to a CSV file on a microSD card. The ILI9341 color display shows live values, min and max, and a two-color live graph of the last 30 readings. Plug the card into your computer and open the file in Excel.

ESP32 Egg Incubator Controller (DHT22 + Relay + Servo + OLED)
Hand the hen's job to an ESP32! The DHT22 measures temperature and humidity, a relay switches the heater with hysteresis, an SG90 servo gently tilts the egg tray every 3 hours, and the 0.96 inch OLED shows the day counter, a temperature graph and alarms. Chicken, quail and duck profiles are built in, and turning stops by itself for the last 3 days. If the sensor fails, the heater switches off for safety.

ESP32 Smart Curtain (NEMA 17 + A4988 + LDR + OLED)
The curtain opens by itself when the sun comes up and closes after dark! An LDR measures the light, an A4988 driver turns a NEMA 17 stepper with a soft start and stop, and the 0.96 inch OLED shows a window drawing, how open the curtain is and a sun or moon. Two buttons open and close it by hand, and holding one stops it halfway. The position is saved to flash, so after a power cut the curtain knows where it is.
