Loyihalar · Arduino / ESP32 / Pico

Arduino loyihalarini kashf qil

Boshlang‘ichdan yuqori darajagacha, sxemali, kodli va videoli yuzlab loyihalar. Qaysi darajada bo‘lsang, o‘sha yerdan boshla.

LED Blink
AR-1Boshlang‘ich

LED Blink

The very first hello of electronics: switching a single LED on and off. The Arduino turns the LED on and off at short intervals, so the light blinks quickly.

4.6(200)
1247
Two LEDs Blinking Alternately
AR-2Boshlang‘ich

Two LEDs Blinking Alternately

Two LEDs blink quickly in turn: when one lights up the other goes off, as if they were tossing a ball back and forth.

4.6(110)
362
Traffic Light
AR-3Boshlang‘ich

Traffic Light

A tiny copy of the traffic light you see on the road every day. Red stays on for two seconds, yellow flashes for a moment, green stays on for two seconds, then it goes back to red through yellow…

4.8(137)
440
LED Police Lights
AR-4Boshlang‘ich

LED Police Lights

Just like the lights on a police car: the red LED flashes three times in quick succession, then the blue LED flashes three times, and the pattern keeps repeating without a break.

4.7(105)
283
LED Control with a Push Button (Push)
AR-9Boshlang‘ich

LED Control with a Push Button (Push)

Just like a doorbell: the light stays on as long as you press, and goes off when you let go.

4.8(114)
253
Toggle an LED with a Button (On/Off)
AR-10Boshlang‘ich

Toggle an LED with a Button (On/Off)

Press the button once and the light comes on, press it again and it goes off, just like the light switch in your room.

4.7(103)
177
Measuring Light Intensity with an LDR
AR-11Boshlang‘ich

Measuring Light Intensity with an LDR

Want to see how bright your room is as a number? The LDR, a small part that reacts to light, measures the light around it, and the Arduino writes the value to your computer screen every half second.

4.6(83)
143
Night Light with Ldr
AR-12Boshlang‘ich

Night Light with Ldr

A little night light that turns on by itself when it gets dark and goes off when morning comes.

4.7(105)
225
LED Blink with ESP32
ES-1Boshlang‘ich

LED Blink with ESP32

Teaches basic GPIO output usage with ESP32. We achieve a blinking effect by turning an LED on and off from a digital pin. ESP32 version of the classic blink project on Arduino UNO; the basic blink commands in the Arduino environment are the same, but the ESP32's pin layout and 3.3 V GPIO levels differ from those of the Arduino UNO.

4.7(37)
108
ESP32 LED Control with Push Button (Push)
ES-2Boshlang‘ich

ESP32 LED Control with Push Button (Push)

The LED lights up when the button is pressed and turns off when released. Shows how the ESP32's digital input pin and internal pull-up resistor are used. The INPUT_PULLUP mode eliminates the need for an external resistor.

4.6(36)
57
ESP32 LED Control with Pushbutton (Toggle)
ES-3Boshlang‘ich

ESP32 LED Control with Pushbutton (Toggle)

Each time the button is pressed the state of the LED changes: if it is on it turns off, if it is off it turns on. Classic toggle pattern. With debounce we clean up the mechanical noise of the pushbutton to ensure a single toggle with a single press.

4.6(39)
59
ESP32 Built-in LED Blink
ES-4Boshlang‘ich

ESP32 Built-in LED Blink

Blinking the built-in blue LED on the ESP32 DevKit V1. No external components required! The first project you should try when you buy an ESP32. GPIO 2 is connected to the built-in LED.

4.8(29)
54