Loyihalar · Arduino / ESP32 / Pico

Arduino loyihalarini kashf qil

Boshlang‘ichdan yuqori darajagacha, sxemali, kodli va videoli yuzlab loyihalar. Qaysi darajada bo‘lsang, o‘sha yerdan boshla.

ESP32 MQ-2 Gas/Smoke Detector Alarm
ES-20O‘rta

ESP32 MQ-2 Gas/Smoke Detector Alarm

In this project, combustible gas (LPG, methane, propane) and smoke detection is performed using an MQ-2 gas sensor module, and a siren-like alarm is played through a passive buzzer upon detection. The sensor's digital threshold output (DO) is connected to GPIO 4 on the ESP32; when gas or smoke exceeds the threshold, DO goes LOW and the alarm is triggered. Sensitivity is adjusted via the module's potentiometer. The passive buzzer is driven using tone() to produce a two-frequency siren effect.

4.7(29)
44
ESP32 RFID RC522 Card Reader (with LCD)
ES-21O‘rta

ESP32 RFID RC522 Card Reader (with LCD)

In this project, we will connect the MFRC522-based RC522 RFID module to the ESP32 via SPI and read the card/tag UID. This forms the basis for applications such as door locks, membership systems, and access control. We will display the read UID on an LCD screen; this version does not compare it with an authorized card list. WARNING: The RC522 operates only at 3.3V; supplying 5V will burn out the module!

4.8(21)
42
Raspberry Pi Pico LED Campfire (8x8 NeoPixel Matrix + Potentiometer + Buzzer)
PI-17O‘rta

Raspberry Pi Pico LED Campfire (8x8 NeoPixel Matrix + Potentiometer + Buzzer)

A campfire that doesn't burn or warm anything, but still crackles! The Raspberry Pi Pico draws a realistic flame on an 8x8 NeoPixel matrix, recalculated every frame: sparks appear at the base, heat cools as it rises and glows from red to white. A potentiometer sets the flame height, a button switches between Fire, Gas, Magic and Amethyst themes, and a buzzer adds the crackle of burning wood. Procedural animation, ADC, PWM and MicroPython in one project.

2
ESP32 IoT Room Station (Relay + DHT22)
ES-99O‘rta
IoT

ESP32 IoT Room Station (Relay + DHT22)

Turn your lamp on from your phone and watch your room's temperature and humidity live, wherever you are. This project is the step-by-step guide to the Room station IoT template in the app, built with an ESP32, a relay module and a DHT22. Go to Workshop › Devices › Add a device and pick Room station; Ohmi prepares the code with your own device key. The code on this page is an example: the key and Wi-Fi details are placeholders.

5.0(1)
4
ESP32 IoT RGB LED Strip (WS2812B)
ES-101O‘rta
IoT

ESP32 IoT RGB LED Strip (WS2812B)

Control your room's light from your phone: pick a color, set the brightness, turn on the rainbow or breathe effect. This project is the step-by-step guide to the RGB LED strip IoT template in the app, built with an ESP32 and a 30-LED WS2812B strip using three wires. Go to Workshop › Devices › Add a device and pick RGB LED strip; Ohmi prepares the code with your own device key. The code on this page is an example: the key and Wi-Fi details are placeholders.

1.0(1)
3
ESP32 IoT Plant Watering (Soil Sensor + Pump)
ES-102O‘rta
IoT

ESP32 IoT Plant Watering (Soil Sensor + Pump)

Let the pump start by itself when the soil in your pot dries out, and watch the soil moisture live on your phone. This project is the step-by-step guide to the Soil moisture + pump IoT template in the app, built with an ESP32, a soil moisture sensor, a relay and a mini water pump. Go to Workshop › Devices › Add a device; Ohmi prepares the code with your own device key. The code on this page is an example: the key and Wi-Fi details are placeholders.

ESP32 IoT Curtain Opener (SG90 Servo)
ES-103O‘rta
IoT

ESP32 IoT Curtain Opener (SG90 Servo)

Tap + or − on your phone and the servo turns to that angle at the same moment: open and close a model curtain, a blind's tilt rod or a small lid from wherever you are. This project is the step-by-step guide to the Servo curtain IoT template in the app, built with an ESP32 and an SG90 servo using just 3 wires. Go to Workshop › Devices › Add a device; Ohmi prepares the code with your own device key. The code on this page is an example: the key and Wi-Fi details are placeholders.

3
ESP32 Bluetooth RGB LED Strip (WS2812B)
ES-110O‘rta
Bluetooth

ESP32 Bluetooth RGB LED Strip (WS2812B)

Change your strip's color, brightness and effect from your phone: the ESP32 connects straight to your phone over its built-in Bluetooth, and the WS2812B strip needs only 3 wires. This project is the step-by-step guide to the RGB LED strip Bluetooth template in the app. Go to Workshop › Devices › Add a device › Bluetooth, pick RGB LED strip and upload the code with Get the code. The Set up as a Bluetooth panel button on this page opens the wizard with this template.

1