AR-45Începător

Configurarea modulului de ceas RTC DS1302

4.5(23)
31 finalizat
Configurarea modulului de ceas RTC DS1302
Pui în funcțiune un mic modul de ceas care păstrează ora chiar și când placa Arduino este oprită. Modulul are propria baterie mică, iar după ce setezi ceasul, data și ora apar pe ecranul calculatorului în fiecare secundă. Alarmele, temporizatoarele și toate proiectele care țin un jurnal încep cu acest pas.

Video

Schemă electrică

Configurarea modulului de ceas RTC DS1302 - Schemă electrică

Cod sursă

C++ (Arduino IDE)
1// ─────────────────────────────────────────
2//   BlueGrays · bluegrays.com
3//   DS1302 RTC Clock Module Setup
4// ─────────────────────────────────────────
5// If the RTC's time is invalid (new module, flat battery) it writes the
6// compile date and time to the DS1302 once, then prints the date and time
7// to the Serial Monitor every second. The module's battery keeps the time
8// with the power off; later starts do not set it again.
9//
10// Pins:
11//   D6 -> RTC CLK
12//   D7 -> RTC DAT
13//   D8 -> RTC RST
14//   RTC VCC to 5V, GND to GND
15
16#include <virtuabotixRTC.h>   // DS1302 library
17
18// Pins: CLK, DAT, RST
19virtuabotixRTC myRTC(6, 7, 8);
20
21void setup() {
22  Serial.begin(9600);   // Serial at 9600 baud
23
24  // Read the RTC first. A year below 2024 or a month outside 1-12 means the time was never set;
25  // write the compile time. If it is valid leave it, so uploading again or power cycling the
26  // Arduino keeps the time.
27  myRTC.updateTime();
28  if (myRTC.year < 2024 || myRTC.month < 1 || myRTC.month > 12) {
29    setFromCompileTime();
30  }
31}
32
33// Writes the compile time (__DATE__ "Oct 28 2026", __TIME__ "13:42:15") to the RTC. Uploading takes
34// a few seconds, so the clock starts that far behind.
35void setFromCompileTime() {
36  const char *date = __DATE__;
37  const char *time = __TIME__;
38  const char *months = "JanFebMarAprMayJunJulAugSepOctNovDec";
39  char monthName[4] = {date[0], date[1], date[2], '\0'};
40
41  int month = (strstr(months, monthName) - months) / 3 + 1;   // "Oct" -> 10
42  int day = atoi(date + 4);
43  int year = atoi(date + 7);
44  int hour = atoi(time);
45  int minute = atoi(time + 3);
46  int second = atoi(time + 6);
47
48  // Day of the week (Sakamoto's method), 0 = Sunday
49  int offsets[] = {0, 3, 2, 5, 0, 3, 5, 1, 4, 6, 2, 4};
50  int y = year - (month < 3);
51  int weekday = (y + y / 4 - y / 100 + y / 400 + offsets[month - 1] + day) % 7;
52  if (weekday == 0) {
53    weekday = 7;   // Monday = 1 ... Sunday = 7
54  }
55
56  // Order: s, min, h, weekday, day, month, year
57  myRTC.setDS1302Time(second, minute, hour, weekday, day, month, year);
58}
59
60void loop() {
61  // Read the current time from the RTC module
62  myRTC.updateTime();
63
64  // Print the time (day/month/year h:m:s)
65  Serial.print("Current Date/Time: ");
66  Serial.print(myRTC.dayofmonth);
67  Serial.print("/");
68  Serial.print(myRTC.month);
69  Serial.print("/");
70  Serial.print(myRTC.year);
71  Serial.print("  ");
72  Serial.print(myRTC.hours);
73  Serial.print(":");
74  Serial.print(myRTC.minutes);
75  Serial.print(":");
76  Serial.println(myRTC.seconds);
77
78  delay(1000);   // Wait 1 s
79}
80

Întrebări frecvente

La ce folosește modulul RTC?

Modulul de ceas în timp real (RTC) păstrează ora și data chiar și când placa Arduino este oprită, datorită bateriei proprii. Contorul millis() al plăcii Arduino se resetează la fiecare pornire, așa că ai nevoie de un RTC pentru a păstra ora reală.

Este suficient să setez ora o singură dată?

Da. Codul citește mai întâi ora din modul; dacă aceasta nu a fost setată niciodată, scrie o singură dată data și ora la care ai compilat codul. Dacă ora este validă, o păstrează, așa că reîncărcarea codului sau oprirea și repornirea plăcii Arduino nu dereglează ceasul. Nu trebuie să comentezi manual nicio linie.

Ceasul se dereglează în timp. Este normal?

DS1302 folosește un cristal de cuarț și poate avea o abatere de câteva secunde pe zi. Pentru un ceas mai precis, este recomandat modulul DS3231 cu compensare de temperatură (aproximativ ±1 minut pe an).

Ce se întâmplă când se descarcă bateria modulului?

Ceasul funcționează cât timp placa Arduino este alimentată; dacă alimentarea se întrerupe și bateria este descărcată, ceasul se resetează și trebuie setat din nou. Bateria CR2032 ține de obicei câțiva ani.