Raspberry Pi Pico W
Komponentlar

Raspberry Pi Pico W

5.0(3)
22
The Raspberry Pi Pico W is a low-cost development board built around the RP2040 microcontroller, with an Infineon CYW43439 wireless chip that adds 2.4 GHz Wi-Fi 4 (802.11n) and Bluetooth 5.2. It has a 133 MHz dual-core ARM Cortex-M0+ processor, 264 KB of SRAM and 2 MB of flash memory. Its pinout is the same as the Raspberry Pi Pico: 26 GPIO (GP0–GP22 and GP26–GP28, the last three with ADC), PWM, I2C, SPI, UART, PIO and an internal temperature sensor. The pins use 3.3 V logic and are not 5 V tolerant; the board is powered from USB or with 1.8–5.5 V on the VSYS pin. Unlike the Pico, the onboard LED is wired to the wireless chip, not to GP25: use Pin("LED") in MicroPython and LED_BUILTIN in Arduino. It can be programmed with MicroPython, the C/C++ SDK and the Arduino IDE; plug it into USB while holding the BOOTSEL button, it shows up as a drive and you drag a UF2 file onto it. The Pico WH is the version with pre-soldered headers that plugs straight into a breadboard. Pico projects that do not need Wi-Fi also run on this board, and it is ideal for web servers, phone control, sensors that send notifications and IoT projects that fetch data from the internet.

Bu komponent ishlatiladigan loyihalar

Raspberry Pi Pico Onboard LED Blink (Pico and Pico W)
PI-1Boshlang‘ich

Raspberry Pi Pico Onboard LED Blink (Pico and Pico W)

The opening project of the Raspberry Pi Pico series! We blink the Pico's green built-in LED to confirm the board works, the classic "Hello World" first experiment. No external parts needed, just the Pico and a USB cable. The code is written in MicroPython, the language officially supported by the Raspberry Pi Foundation.

5.0(1)
10
Raspberry Pi Pico: Controlling an External LED (Breadboard)
PI-2Boshlang‘ich

Raspberry Pi Pico: Controlling an External LED (Breadboard)

The next step after the Pico's built-in LED: connect an external LED on a breadboard and control it through pin GP14. You'll learn how to use any of the Pico's GPIO pins as an output, the LED's polarity (long leg = anode/+, short leg = cathode/–) and why a current-limiting resistor (220Ω) is a must. Without the resistor, too much current flows through the LED and it can burn out.

4.5(2)
7
Raspberry Pi Pico Alternating Two LEDs (Blink-Flip Pattern)
PI-3Boshlang‘ich

Raspberry Pi Pico Alternating Two LEDs (Blink-Flip Pattern)

The next step after the Pico's single LED: the classic flip-flop animation, with two LEDs blinking in turn. One LED turns off as the other turns on, the most basic example of handling multiple GPIOs. Two LEDs of different colors (red on GP14, green on GP13) swap every 500 ms. With MicroPython's Pin.toggle() method, the code stays short and readable.

5.0(2)
19
Raspberry Pi Pico Traffic Light Simulator (3 LEDs Sequential)
PI-4Boshlang‘ich

Raspberry Pi Pico Traffic Light Simulator (3 LEDs Sequential)

We recreate real traffic light logic with red, yellow and green LEDs, the first Pico project to move up to 3 LEDs! Green says "go" for 4 seconds, yellow "get ready" for 1.5 seconds, red "stop" for 3 seconds, and red+yellow "set off" for 1 second (the European traffic light pattern). You'll learn to define functions (def all_off()), state machine logic and multi-GPIO synchronization.

4.0(1)
12
Raspberry Pi Pico Police Strobe Light Effect (Red + Blue)
PI-5Boshlang‘ich

Raspberry Pi Pico Police Strobe Light Effect (Red + Blue)

We simulate a police car's light bar with a Raspberry Pi Pico in its simplest form! The red and blue LEDs take turns (flip-flop): while red is on, blue is off, and they swap every 0.3 seconds, forever. The code writes the two steps directly in a single while True loop; the speed is set with the WAIT_MS constant.

4.7(3)
10
Raspberry Pi Pico Chasing LED (6 LEDs)
PI-7Boshlang‘ich

Raspberry Pi Pico Chasing LED (6 LEDs)

The classic "running LED" animation with the Pico, 6-LED version! Six LEDs light up one after another from left to right, as if the light were walking along the row. You'll learn Python lists (LED_PINS = [14, 13, 12, 11, 10, 9]), list comprehensions, controlling pins with a for loop and enumerate(). Six LEDs go on pins GP9-GP14, each with a 220Ω current-limiting resistor.

5.0(1)
9
Raspberry Pi Pico 3-Burst Police Flip-Flop (2 LEDs)
PI-6Boshlang‘ich

Raspberry Pi Pico 3-Burst Police Flip-Flop (2 LEDs)

Rhythmic variation of the police strobe project — 3-burst flip-flop! Same 2-LED circuit (GP11 red + GP12 blue), but a different pattern: red LED flashes 3 times rapidly, then blue flashes 3 times, forever. This "burst + switch" pattern is the most recognizable rhythm of real police siren lights. Learn parametrized function def burst(led, count, duration_ms), rhythm design, and generating different visual effects with code on same circuit.

5.0(1)
16
Raspberry Pi Pico Knight Rider LED Scanner (6 LED Back-Forth)
PI-8Boshlang‘ich

Raspberry Pi Pico Knight Rider LED Scanner (6 LED Back-Forth)

Classic "Knight Rider" LED scanner effect with Pico! 6 LEDs go left-to-right, then right-to-left, forever. Like the front grille of KITT car from the iconic 80s TV series. This project is an upgrade of the Chasing LED project: same 6 LED circuit (GP9-GP14), different code pattern. Learn reversed() function for list reversal, two separate for loops for back-and-forth pattern, and generating multiple animations on same circuit.

5.0(1)
14
Raspberry Pi Pico Button Controlled LED (Push)
PI-9Boshlang‘ich
Premium

Raspberry Pi Pico Button Controlled LED (Push)

First input project with Pico — button read! LED lights while button is pressed, off when released. This is the big step after LED animations: signal input from the world to Pico. Learn Pin.IN (input mode), Pin.PULL_UP (internal pull-up resistor — standard for buttons), button.value() reading. GP14 LED, GP2 button (internal PULL_UP). Pressed = LOW (0), released = HIGH (1) — reverse logic seems confusing at first but is industry standard.

11
Raspberry Pi Pico Button Toggle LED
PI-10Boshlang‘ich

Raspberry Pi Pico Button Toggle LED

Button + LED — next level! Unlike the basic button project, there is no need to hold the button. Press and release → LED on. Press and release again → LED off (toggle). Same circuit (LED GP14, Button GP2), but big code difference. Learn edge detection (capturing the 1→0 falling moment), state tracking, debounce (mechanical bounce filter). MicroPython's led.toggle() swaps state in one line. Foundation of all interactive button projects (mode switcher, IRQ, double-click).

10
Raspberry Pi Pico Traffic Light with 4-Mode Button Selector (State Machine)
PI-12O‘rta

Raspberry Pi Pico Traffic Light with 4-Mode Button Selector (State Machine)

4 traffic light modes with 1 button! Each press switches the mode: Normal cycle (red → yellow → green), Red Only (stop), Flashing Yellow (caution/night mode) and Off (maintenance). You'll learn the state machine (the mode variable decides which behavior runs) and cycling through the modes with (mode + 1) % 4.

5.0(1)
16
Raspberry Pi Pico: Independent Control of 2 LEDs Using 2 Buttons
PI-11Boshlang‘ich
Premium

Raspberry Pi Pico: Independent Control of 2 LEDs Using 2 Buttons

2 buttons, 2 LEDs, completely independent of each other! Each button controls its own LED: press BTN1 and the red LED lights up, press BTN2 and the green one does. Press both at once and both LEDs light up (parallel operation). You'll learn to manage several Pin objects together, the ternary operator, Python's compact if-else (1 if x else 0), and a GPIO map (GP12/13 LED outputs, GP4/5 button inputs).

7

Tegishli asboblar