Loyihalar · Arduino / ESP32 / Pico

Arduino loyihalarini kashf qil

Boshlang‘ichdan yuqori darajagacha, sxemali, kodli va videoli yuzlab loyihalar. Qaysi darajada bo‘lsang, o‘sha yerdan boshla.

3x4 Keypad Operation
AR-61Boshlang‘ich

3x4 Keypad Operation

The Arduino instantly knows which key you press on a 12-key keypad that looks like a phone dial pad, and writes it on your computer screen.

4.5(24)
32
LED Blink with ESP32
ES-1Boshlang‘ich

LED Blink with ESP32

Teaches basic GPIO output usage with ESP32. We achieve a blinking effect by turning an LED on and off from a digital pin. ESP32 version of the classic blink project on Arduino UNO; the basic blink commands in the Arduino environment are the same, but the ESP32's pin layout and 3.3 V GPIO levels differ from those of the Arduino UNO.

4.7(37)
108
ESP32 LED Control with Push Button (Push)
ES-2Boshlang‘ich

ESP32 LED Control with Push Button (Push)

The LED lights up when the button is pressed and turns off when released. Shows how the ESP32's digital input pin and internal pull-up resistor are used. The INPUT_PULLUP mode eliminates the need for an external resistor.

4.6(36)
57
ESP32 LED Control with Pushbutton (Toggle)
ES-3Boshlang‘ich

ESP32 LED Control with Pushbutton (Toggle)

Each time the button is pressed the state of the LED changes: if it is on it turns off, if it is off it turns on. Classic toggle pattern. With debounce we clean up the mechanical noise of the pushbutton to ensure a single toggle with a single press.

4.6(39)
59
ESP32 Built-in LED Blink
ES-4Boshlang‘ich

ESP32 Built-in LED Blink

Blinking the built-in blue LED on the ESP32 DevKit V1. No external components required! The first project you should try when you buy an ESP32. GPIO 2 is connected to the built-in LED.

4.8(29)
54
ESP32 Traffic Light
ES-5Boshlang‘ich

ESP32 Traffic Light

Real traffic light simulation with 3 LEDs red-yellow-green. Timings close to real traffic logic: red long, yellow short, green long. Classic example of sequential GPIO control.

4.4(22)
45
ESP32 Knight Rider LED
ES-6Boshlang‘ich

ESP32 Knight Rider LED

6 LEDs moving sequentially from left to right and right to left (Knight Rider style). A basic example of using for loops and arrays. Teaches the logic of direction change.

4.5(19)
33
ESP32 LED Fade with PWM
ES-8Boshlang‘ich

ESP32 LED Fade with PWM

Smoothly changing the brightness of the LED from 0 to max, from max to 0. We control PWM with analogWrite() as in Arduino - the same syntax as ESP32 Arduino Core 3.0+ works without problems. Pin definition + pinMode + analogWrite is enough.

4.8(36)
55
ESP32 RGB LED Control
ES-9Boshlang‘ich

ESP32 RGB LED Control

Unlimited color generation with a single RGB LED instead of 3 separate LEDs. As in Arduino, we make a rainbow transition by setting the R/G/B values with analogWrite(). Color theory (such as red+green=yellow) is seen practically.

4.6(29)
52
Reading Light Intensity with the ESP32 LDR Module
ES-11Boshlang‘ich

Reading Light Intensity with the ESP32 LDR Module

Real-time monitoring of the LDR module's raw ADC value and relative light percentage calculated from dark and light reference values in the Serial Monitor. This percentage is not a lux measurement. Teaches the module’s calibration logic. It is ideal to complete this before Project 10, as it is used to determine the threshold value.

4.6(36)
55
Raspberry Pi Pico Onboard LED Blink (Pico and Pico W)
PI-1Boshlang‘ich

Raspberry Pi Pico Onboard LED Blink (Pico and Pico W)

The opening project of the Raspberry Pi Pico series! We blink the Pico's green built-in LED to confirm the board works, the classic "Hello World" first experiment. No external parts needed, just the Pico and a USB cable. The code is written in MicroPython, the language officially supported by the Raspberry Pi Foundation.

5.0(1)
10
Raspberry Pi Pico: Controlling an External LED (Breadboard)
PI-2Boshlang‘ich

Raspberry Pi Pico: Controlling an External LED (Breadboard)

The next step after the Pico's built-in LED: connect an external LED on a breadboard and control it through pin GP14. You'll learn how to use any of the Pico's GPIO pins as an output, the LED's polarity (long leg = anode/+, short leg = cathode/–) and why a current-limiting resistor (220Ω) is a must. Without the resistor, too much current flows through the LED and it can burn out.

4.5(2)
7