111 dự án khối lệnh · Arduino · ESP32 · Pico
Lập trình khối cho dự án Arduino, ESP32 và Pico
Theo dõi các khối lệnh nhiều màu thay vì đọc code từng dòng. 111 dự án BlueGrays có phiên bản khối lệnh, và mỗi khối tương ứng với một dòng code thật chạy trên bo mạch.
Lập trình khối là gì?
Lập trình khối là tạo chương trình bằng các khối giống mảnh ghép thay vì gõ chữ. "Đặt chân làm đầu ra", "bật LED" và "chờ 1 giây" đều là các khối, và xếp chúng lại sẽ thành chương trình. Không phải lo dấu chấm phẩy, dấu ngoặc hay lỗi gõ, nên bạn tập trung được vào logic.
BlueGrays dùng bộ khối lệnh riêng, và các khối nói ngôn ngữ của bạn: nếu ứng dụng dùng tiếng Anh, trên khối sẽ ghi "repeat forever" và "write HIGH to pin". Trong dự án Arduino và ESP32, khối lệnh tương ứng với code C++; trong dự án Raspberry Pi Pico, chúng tương ứng với MicroPython.
Mục tiêu không phải là dùng khối lệnh mãi mà là hiểu code. Đặt khối lệnh của một dự án cạnh code của nó, bạn sẽ thấy mỗi dòng làm gì. Sau vài dự án, bạn bắt đầu đọc code mà không cần khối lệnh.
Lập trình khối hoạt động thế nào trong BlueGrays
Trong ứng dụng, khối lệnh nằm ở phần code của mọi dự án khối lệnh. Bốn bước:
- 01
Chọn một dự án khối lệnh
Các dự án có huy hiệu khối lệnh đi kèm phiên bản khối lệnh. Bạn cũng có thể lọc danh sách để chỉ hiện dự án khối lệnh.
- 02
Bật "Hiển thị dạng khối"
Một công tắc trong phần code biến code thành khối lệnh. Chạm vào ảnh để mở toàn màn hình và phóng to.
- 03
Hiểu khối lệnh
Tab "Hiểu khối lệnh" dẫn bạn qua chương trình từng bước, chỉ hiện các khối của mỗi bước và việc chúng làm.
- 04
Chuyển sang code thật
Tắt công tắc và chương trình đó sẽ hiện dưới dạng code. Sao chép vào Arduino IDE (hoặc Thonny cho Pico) rồi nạp vào bo mạch.
Một chương trình: khối lệnh và code
Bên trái là khối lệnh của dự án. Bên phải là code chạy trên bo mạch. Mỗi khối có một dòng code tương ứng.
Khối lệnh

Code
1// ─────────────────────────────────────────
2// BlueGrays · bluegrays.com
3// LED Blink
4// ─────────────────────────────────────────
5// Blinks a single LED on and off every 100 ms. Shows the basic use of the
6// digitalWrite and delay functions.
7//
8// Pins:
9// D9 -> LED (with a 220 ohm resistor)
10
11void setup() {
12 pinMode(9,OUTPUT); // LED pin as output
13}
14
15void loop() {
16 digitalWrite(9,HIGH); // Turn the LED on
17 delay(100); // Wait 100 ms (1000 ms = 1 s)
18 digitalWrite(9,LOW); // Turn the LED off
19 delay(100);
20}
21Dự án khối lệnh
Mọi dự án có phiên bản khối lệnh, theo nền tảng. Dự án miễn phí được xếp trước: 31 dự án hoàn toàn miễn phí, gồm cả khối lệnh và code.
Dự án Arduino74 dự án khối lệnh

LED Blink
The very first hello of electronics: switching a single LED on and off. The Arduino turns the LED on and off at short intervals, so the light blinks quickly.

Two LEDs Blinking Alternately
Two LEDs blink quickly in turn: when one lights up the other goes off, as if they were tossing a ball back and forth.

Traffic Light
A tiny copy of the traffic light you see on the road every day. Red stays on for two seconds, yellow flashes for a moment, green stays on for two seconds, then it goes back to red through yellow…

LED Police Lights
Just like the lights on a police car: the red LED flashes three times in quick succession, then the blue LED flashes three times, and the pattern keeps repeating without a break.

LED Chaser
Lights that switch on one after another, as if they were running. The Arduino lights six LEDs one at a time; each glows for a brief moment and goes out, so the light walks from start to end and then…

Knight Rider LED Effect
The classic scanner light: a dot of light slides from one end of six LEDs to the other and then comes back.

LED Chaser with Adjustable Speed
Six LEDs light up one after another, so the light seems to run from one end to the other.

Knight Rider LED Effect with Adjustable Speed
A light runs from one end of six LEDs to the other, turns around and runs back again.
Dự án Arduino: tất cả dự án khối lệnh
- AR-9LED Control with a Push Button (Push)Miễn phí
- AR-10Toggle an LED with a Button (On/Off)Miễn phí
- AR-11Measuring Light Intensity with an LDRMiễn phí
- AR-12Night Light with LdrMiễn phí
- AR-13Using a BuzzerMiễn phí
- AR-14Frequency Setting with BuzzerMiễn phí
- AR-27HC-SR04 Distance Measurement (Serial Display)Miễn phí
- AR-37Reading a Reed SwitchMiễn phí
- AR-45DS1302 RTC Clock Module SetupMiễn phí
- AR-55Temperature and Humidity with DHT11Miễn phí
- AR-613x4 Keypad OperationMiễn phí
- AR-16Reading IR Remote Control Codes
- AR-17Led On/Off with IR Receiver and Remote Control
- AR-19Lighting 220V Bulb with Push Button
- AR-20Lighting 220V Bulb with Button (On-Off)
- AR-21Lighting 220V Bulb with Remote Control
- AR-22Laser Warning System
- AR-23Laser Security System
- AR-24Motion Detector with Motion Sensor
- AR-25Doorbell and Light with Motion Sensor
- AR-26Simple Piano with Buzzer and Button
- AR-28Parking Sensor with HC-SR04
- AR-29Print Message on 2x16 LCD Screen
- AR-30Bouncing Text Animation on LCD
- AR-31Measuring Distance Using LCD Display
- AR-32Using LCD Screen with I2C
- AR-33Height Measurement Project
- AR-34Control an LED from Your Phone via Bluetooth
- AR-35Using a Servo Motor
- AR-36Servo Motor Operation with Potentiometer
- AR-38Reed Switch Door Sensor
- AR-39Using an RGB LED
- AR-40Smooth Color Transition with RGB Led
- AR-42Displaying Numbers 0-99 on a 7-Segment Display
- AR-43Counter with 7-Segment Display and Buttons
- AR-44Temperature Measurement with NTC and 2x16 Lcd Display
- AR-46DS1302 RTC Clock with LCD Display
- AR-47Displaying 0-9999 on a 4-Digit 7-Segment Display
- AR-48Digital Clock with 4-Digit 7-Segment Display
- AR-49Bomb Animation with 4-Digit 7-Segment Display
- AR-50Using a Flame Sensor
- AR-51Using a Gas Sensor
- AR-52Flame and Gas Sensor Alarm
- AR-53RFID Value Reading
- AR-54RFID Authentication
- AR-56Digital Voltmeter with LCD Display
- AR-58Two-Way Communication Between 2 Arduinos
- AR-59Led Control with Joystick
- AR-60Servo Control with Joystick
- AR-62LED Control with a 3x4 Keypad
- AR-634x4 Keypad Operation
- AR-64Password Lock with 4x4 Keypad and LCD
- AR-67Using a Stepper Motor
- AR-68360-Degree Servo from a Stepper Motor
- AR-69Using a WS2812B LED Strip
- AR-70Police Lights with WS2812B
- AR-71WS2812B LED Chaser
- AR-72WS2812B LED Chaser (Fill Effect)
- AR-73WS2812B Knight Rider Effect
- AR-74WS2812B Knight Rider Effect (3 LEDs)
- AR-75WS2812B Animation 1
- AR-77Reading Reflection (Proximity) with TCRT5000
- AR-78TCRT5000 Black and White Surface Detection
- AR-82Smart Stair and Corridor Lighting
- AR-83Smart Irrigation Station
- AR-95Arduino Reaction Time Test with Sound Cue: Measure Your Reflexes in Milliseconds (LCD + Buzzer + 3 LEDs)
Dự án ESP3223 dự án khối lệnh

LED Blink with ESP32
Teaches basic GPIO output usage with ESP32. We achieve a blinking effect by turning an LED on and off from a digital pin. ESP32 version of the classic blink project on Arduino UNO; the basic blink commands in the Arduino environment are the same, but the ESP32's pin layout and 3.3 V GPIO levels differ from those of the Arduino UNO.

ESP32 LED Control with Push Button (Push)
The LED lights up when the button is pressed and turns off when released. Shows how the ESP32's digital input pin and internal pull-up resistor are used. The INPUT_PULLUP mode eliminates the need for an external resistor.

ESP32 LED Control with Pushbutton (Toggle)
Each time the button is pressed the state of the LED changes: if it is on it turns off, if it is off it turns on. Classic toggle pattern. With debounce we clean up the mechanical noise of the pushbutton to ensure a single toggle with a single press.

ESP32 Built-in LED Blink
Blinking the built-in blue LED on the ESP32 DevKit V1. No external components required! The first project you should try when you buy an ESP32. GPIO 2 is connected to the built-in LED.

ESP32 Traffic Light
Real traffic light simulation with 3 LEDs red-yellow-green. Timings close to real traffic logic: red long, yellow short, green long. Classic example of sequential GPIO control.

ESP32 Knight Rider LED
6 LEDs moving sequentially from left to right and right to left (Knight Rider style). A basic example of using for loops and arrays. Teaches the logic of direction change.

ESP32 LED Fade with PWM
Smoothly changing the brightness of the LED from 0 to max, from max to 0. We control PWM with analogWrite() as in Arduino - the same syntax as ESP32 Arduino Core 3.0+ works without problems. Pin definition + pinMode + analogWrite is enough.

ESP32 RGB LED Control
Unlimited color generation with a single RGB LED instead of 3 separate LEDs. As in Arduino, we make a rainbow transition by setting the R/G/B values with analogWrite(). Color theory (such as red+green=yellow) is seen practically.
Dự án ESP32: tất cả dự án khối lệnh
- ES-11Reading Light Intensity with the ESP32 LDR ModuleMiễn phí
- ES-14ESP32 HC-SR04 Ultrasonic Distance SensorMiễn phí
- ES-15ESP32 DHT22 Temperature and Humidity (with LCD Display)Miễn phí
- ES-20ESP32 MQ-2 Gas/Smoke Detector AlarmMiễn phí
- ES-21ESP32 RFID RC522 Card Reader (with LCD)Miễn phí
- ES-7ESP32 Police Strobe Light Effect
- ES-10ESP32 Night Light with LDR
- ES-12ESP32 Melody Playback with Buzzer
- ES-13ESP32 LED Brightness Control with a Potentiometer (Analog → PWM)
- ES-16ESP32 Servo Motor (Potentiometer Control)
- ES-17ESP32 I2C LCD Display (16x2)
- ES-18Digital Clock with ESP32 and DS1307 RTC (I2C + LCD)
- ES-19Automatic Lighting with the ESP32 PIR Motion Sensor
- ES-23ESP32 TM1637 4-Digit 7-Segment Display
- ES-24ESP32 WS2812B NeoPixel Strip Control
Dự án Raspberry Pi Pico10 dự án khối lệnh

Raspberry Pi Pico Onboard LED Blink (Pico and Pico W)
The opening project of the Raspberry Pi Pico series! We blink the Pico's green built-in LED to confirm the board works, the classic "Hello World" first experiment. No external parts needed, just the Pico and a USB cable. The code is written in MicroPython, the language officially supported by the Raspberry Pi Foundation.

Raspberry Pi Pico: Controlling an External LED (Breadboard)
The next step after the Pico's built-in LED: connect an external LED on a breadboard and control it through pin GP14. You'll learn how to use any of the Pico's GPIO pins as an output, the LED's polarity (long leg = anode/+, short leg = cathode/–) and why a current-limiting resistor (220Ω) is a must. Without the resistor, too much current flows through the LED and it can burn out.

Raspberry Pi Pico Alternating Two LEDs (Blink-Flip Pattern)
The next step after the Pico's single LED: the classic flip-flop animation, with two LEDs blinking in turn. One LED turns off as the other turns on, the most basic example of handling multiple GPIOs. Two LEDs of different colors (red on GP14, green on GP13) swap every 500 ms. With MicroPython's Pin.toggle() method, the code stays short and readable.

Raspberry Pi Pico Traffic Light Simulator (3 LEDs Sequential)
We recreate real traffic light logic with red, yellow and green LEDs, the first Pico project to move up to 3 LEDs! Green says "go" for 4 seconds, yellow "get ready" for 1.5 seconds, red "stop" for 3 seconds, and red+yellow "set off" for 1 second (the European traffic light pattern). You'll learn to define functions (def all_off()), state machine logic and multi-GPIO synchronization.

Raspberry Pi Pico Police Strobe Light Effect (Red + Blue)
We simulate a police car's light bar with a Raspberry Pi Pico in its simplest form! The red and blue LEDs take turns (flip-flop): while red is on, blue is off, and they swap every 0.3 seconds, forever. The code writes the two steps directly in a single while True loop; the speed is set with the WAIT_MS constant.

Raspberry Pi Pico 3-Burst Police Flip-Flop (2 LEDs)
Rhythmic variation of the police strobe project — 3-burst flip-flop! Same 2-LED circuit (GP11 red + GP12 blue), but a different pattern: red LED flashes 3 times rapidly, then blue flashes 3 times, forever. This "burst + switch" pattern is the most recognizable rhythm of real police siren lights. Learn parametrized function def burst(led, count, duration_ms), rhythm design, and generating different visual effects with code on same circuit.

Raspberry Pi Pico Button Toggle LED
Button + LED — next level! Unlike the basic button project, there is no need to hold the button. Press and release → LED on. Press and release again → LED off (toggle). Same circuit (LED GP14, Button GP2), but big code difference. Learn edge detection (capturing the 1→0 falling moment), state tracking, debounce (mechanical bounce filter). MicroPython's led.toggle() swaps state in one line. Foundation of all interactive button projects (mode switcher, IRQ, double-click).

Raspberry Pi Pico PWM LED Fade (Breathing Effect)
The LED doesn't just blink anymore, it breathes! With the Raspberry Pi Pico's PWM (Pulse Width Modulation), the LED's brightness slowly rises and then slowly fades, a calm "breathing" effect like a sleeping laptop's light. You'll learn the machine.PWM class, the 16-bit brightness value from 0–65535 with duty_u16() and the PWM frequency.
Dự án Raspberry Pi Pico: tất cả dự án khối lệnh
Dành cho ai?
Trẻ em và phụ huynh
Lập trình cho trẻ em sẽ nhớ lâu hơn nhiều khi kết thúc bằng một chiếc LED sáng lên trên bàn. Khối lệnh giúp chương trình dễ đọc, và hai người cùng nhau lắp mạch.
Giáo viên và câu lạc bộ
Trong lớp robot hoặc STEM, bạn có thể giải thích dự án bằng khối lệnh trước rồi chuyển sang code. Mỗi dự án đều có sẵn danh sách linh kiện và sơ đồ mạch.
Người mới bắt đầu
Lập trình khối Arduino là cách nhanh nhất để nắm logic của vài dự án đầu tiên. Hãy bắt đầu bằng khối lệnh và chuyển sang code khi bạn thấy sẵn sàng.
Câu hỏi thường gặp
Lập trình dựa trên khối là gì?
Đó là cách lập trình mà các lệnh được hiển thị dưới dạng khối ghép lại như mảnh ghép thay vì văn bản gõ tay. Vì không thể gõ sai, người mới và trẻ em hiểu logic của chương trình dễ hơn.
Có bao nhiêu dự án BlueGrays có khối lệnh?
Hiện có 111: 76 dự án Arduino, 25 dự án ESP32 và 10 dự án Raspberry Pi Pico. Danh sách sẽ tăng dần khi có thêm dự án được chuyển đổi.
Lập trình khối có miễn phí không?
Ứng dụng miễn phí. Khối lệnh và code của 31 dự án khối lệnh mở cho mọi người. Ở các dự án khác, khối lệnh được mở khóa với Premium, giống như code.
Có thể nạp khối lệnh thẳng vào bo mạch không?
Không. Khối lệnh giúp chương trình dễ đọc và dễ hiểu hơn; thứ được nạp vào bo mạch luôn là code thật của dự án. Bạn sao chép code vào Arduino IDE, hoặc Thonny cho Pico, rồi nạp.
Tôi có thể tự tạo chương trình bằng khối lệnh không?
Chưa được. Chúng tôi chuẩn bị khối lệnh cho từng dự án và khớp chúng với code từng dòng một, nên khối lệnh bạn thấy luôn đại diện cho một chương trình đã được kiểm tra và chạy được.
Khác gì so với Scratch hay mBlock?
Trong Scratch và mBlock, bạn kéo thả khối trên máy tính để viết chương trình của riêng mình. Trong BlueGrays, mỗi dự án khối lệnh đi kèm sơ đồ mạch, danh sách linh kiện và code thật, còn khối lệnh là phiên bản dễ đọc của code đó. Hai cách này bổ sung cho nhau.
Có phù hợp với trẻ em không? Bao nhiêu tuổi thì bắt đầu được?
Trẻ khoảng 9 hoặc 10 tuổi đọc tốt có thể bắt đầu cùng người lớn. Các dự án đầu tiên không cần hàn: chúng được lắp trên breadboard với LED, nút nhấn và còi chip.
Khối lệnh có những ngôn ngữ nào?
Tiếng Anh, Thổ Nhĩ Kỳ, Đức, Tây Ban Nha, Pháp và Ý. Khối lệnh hiển thị theo ngôn ngữ bạn dùng trong ứng dụng.

