Binary clock gamit ang Raspberry Pi Pico (6 LED + button)
Walang digit ang orasang ito! Gagawa tayo ng orasan gamit ang Raspberry Pi Pico na nagpapakita ng oras sa binary. Ang 6 LED ay ang mga puwestong 32-16-8-4-2-1; pagsamahin ang mga nakasindi at mababasa mo ang segundo, minuto o oras. Isang button lang ang naglilipat ng field at nagtatakda ng oras, at may dumaraang sinag ng ilaw sa mga LED bawat buong oras.

Video
Circuit diagram

Source code
1# ─────────────────────────────────────────
2# BlueGrays · bluegrays.com
3# Raspberry Pi Pico Binary Clock (6 LEDs + Button)
4# ─────────────────────────────────────────
5# A clock that shows the time as binary numbers. The 6 LEDs are the
6# 32-16-8-4-2-1 places; the lit LEDs add up to the value. A short press
7# switches between seconds, minutes and hours; a long press sets the
8# field. Every full hour a light sweep runs, and the onboard LED ticks the
9# seconds.
10#
11# Pins:
12# GP2 -> LED 1 (bit 0), through 220 ohm
13# GP3 -> LED 2 (bit 1), through 220 ohm
14# GP4 -> LED 4 (bit 2), through 220 ohm
15# GP5 -> LED 8 (bit 3), through 220 ohm
16# GP6 -> LED 16 (bit 4), through 220 ohm
17# GP7 -> LED 32 (bit 5), through 220 ohm
18# GP15 -> Button (other leg to GND)
19# LED -> Onboard LED (seconds tick)
20# GND -> LED cathodes, button
21
22from machine import Pin
23import time
24
25# ============ SETTINGS ============
26START_TIME = (12, 59, 50) # Start time (h, m, s)
27SEC, MIN, HOUR = range(3)
28START_MODE = SEC # Field shown at start
29LONG_MS = 800 # Long press time
30DEBOUNCE_MS = 20 # Button debounce time
31MODE_MS = 500 # How long the mode marker shows
32BLINK_MS = 300 # Blink period in set mode
33SET_TIMEOUT_MS = 10000 # Set mode saves after this idle time
34SWEEP_STEP_MS = 60 # Step of the full hour sweep
35SWEEP_ROUNDS = 2 # Number of sweeps
36TICK_MS = 100 # Onboard LED flash length
37LOOP_MS = 5 # Loop step
38
39# In order bit 0 (1) ... bit 5 (32)
40LED_PINS = (2, 3, 4, 5, 6, 7)
41MODE_NAMES = ("SECONDS", "MINUTES", "HOURS")
42# Mode marker: 1, 2 or 3 LEDs from the left (seconds, minutes, hours)
43MODE_MARKS = (0b100000, 0b110000, 0b111000)
44
45
46# ============ HARDWARE ============
47leds = [Pin(gp, Pin.OUT, value=0) for gp in LED_PINS]
48# The name "LED" finds the onboard LED on both the Pico and the Pico W (not a GP pin on the W)
49tick_led = Pin("LED", Pin.OUT, value=0) # The Pico's onboard LED
50
51
52class Button:
53 # Pull-up button: reads 0 when pressed. update() 1 = pressed, -1 = released
54 def __init__(self, gp):
55 self.pin = Pin(gp, Pin.IN, Pin.PULL_UP)
56 self.down = False
57 self.changed_at = time.ticks_ms()
58
59 def update(self, now):
60 pressed = self.pin.value() == 0
61 if pressed != self.down and time.ticks_diff(now, self.changed_at) >= DEBOUNCE_MS:
62 self.down = pressed
63 self.changed_at = now
64 return 1 if pressed else -1
65 return 0
66
67 def held_ms(self, now):
68 return time.ticks_diff(now, self.changed_at)
69
70
71button = Button(15)
72shown = -1 # Last pattern on the LEDs
73
74
75def show_bits(pattern):
76 # If the pattern changed, write the 6 LEDs: bit i -> LED i
77 global shown
78 if pattern == shown:
79 return
80 shown = pattern
81 for i, led in enumerate(leds):
82 led.value((pattern >> i) & 1)
83
84
85def binary(v):
86 # 6 digit binary text, e.g. 13 -> 001101
87 return "".join("1" if v >> i & 1 else "0" for i in range(5, -1, -1))
88
89
90# ============ CLOCK ============
91clock_s = (START_TIME[0] * 3600 + START_TIME[1] * 60 + START_TIME[2]) % 86400
92start = time.ticks_ms()
93next_second = time.ticks_add(start, 1000)
94tick_off_at = start
95
96
97def hms():
98 return clock_s // 3600, clock_s // 60 % 60, clock_s % 60
99
100
101def field_value(m):
102 h, mi, s = hms()
103 return (s, mi, h)[m]
104
105
106def time_text():
107 return "%02d:%02d:%02d" % hms()
108
109
110# ============ STATE ============
111mode = START_MODE
112setting = False # Set mode
113long_done = False # Long press handled for this press
114marker_until = start # When the mode marker ends
115sweep_at = None # Start of the light sweep
116blink_ref = start # Start of the blink cycle
117last_press = start # Last press in set mode
118
119
120def report(prefix):
121 v = field_value(mode)
122 print("%s %s: %d = %s (%s)" % (prefix, MODE_NAMES[mode], v, binary(v), time_text()))
123
124
125def save_setting(now):
126 global setting
127 setting = False
128 print("Time set: %s" % time_text())
129
130
131def on_short(now):
132 global mode, marker_until, clock_s, blink_ref, last_press
133 if setting:
134 # In set mode every short press adds 1 to the selected field
135 h, mi, s = hms()
136 if mode == HOUR:
137 h = (h + 1) % 24
138 else:
139 mi = (mi + 1) % 60
140 clock_s = h * 3600 + mi * 60 + s
141 blink_ref = now
142 last_press = now
143 report("+1")
144 else:
145 mode = (mode + 1) % 3
146 marker_until = time.ticks_add(now, MODE_MS)
147 report("Mode")
148
149
150def on_long(now):
151 global setting, clock_s, next_second, blink_ref, last_press
152 if setting:
153 if mode == MIN:
154 # After setting the minutes, the seconds restart from zero
155 clock_s -= clock_s % 60
156 next_second = time.ticks_add(now, 1000)
157 save_setting(now)
158 elif mode == SEC:
159 # In seconds mode a long press zeroes the seconds (sync to a time signal)
160 clock_s -= clock_s % 60
161 next_second = time.ticks_add(now, 1000)
162 print("Seconds zeroed: %s" % time_text())
163 else:
164 setting = True
165 blink_ref = now
166 last_press = now
167 report("Set")
168
169
170def frame(now):
171 # The LED pattern right now: sweep > mode marker > set (blinking) > value
172 if sweep_at is not None:
173 step = time.ticks_diff(now, sweep_at) // SWEEP_STEP_MS
174 pos = step % 10
175 return 1 << (pos if pos < 6 else 10 - pos) # back and forth
176 if time.ticks_diff(marker_until, now) > 0:
177 return MODE_MARKS[mode]
178 if setting and time.ticks_diff(now, blink_ref) // BLINK_MS % 2:
179 return 0
180 return field_value(mode)
181
182
183# ============ MAIN LOOP ============
184print("== BlueGrays · bluegrays.com ==")
185print("Pico Binary Clock")
186print("Short press: next field, long: set")
187print("LEDs: 32 16 8 4 2 1")
188report("Mode")
189
190next_loop = time.ticks_ms()
191while True:
192 now = time.ticks_ms()
193
194 # Second counter: each next second is added to the last one, so it never drifts
195 if time.ticks_diff(now, next_second) >= 0:
196 next_second = time.ticks_add(next_second, 1000)
197 clock_s = (clock_s + 1) % 86400
198 tick_led.value(1)
199 tick_off_at = time.ticks_add(now, TICK_MS)
200 if clock_s % 60 == 0:
201 print("Time %s" % time_text()[:5])
202 if clock_s % 3600 == 0 and not setting:
203 sweep_at = now # Full hour: light sweep
204 if not setting and time.ticks_diff(now, tick_off_at) >= 0:
205 tick_led.value(0)
206 if sweep_at is not None and time.ticks_diff(now, sweep_at) >= SWEEP_STEP_MS * 10 * SWEEP_ROUNDS:
207 sweep_at = None
208
209 # Button: a short press acts on release, a long press as soon as LONG_MS passes
210 b = button.update(now)
211 if b == 1:
212 long_done = False
213 sweep_at = None # A press stops the sweep
214 elif button.down and not long_done and button.held_ms(now) >= LONG_MS:
215 long_done = True
216 on_long(now)
217 elif b == -1 and not long_done:
218 on_short(now)
219
220 if setting:
221 tick_led.value(1) # Onboard LED on while setting
222 if time.ticks_diff(now, last_press) >= SET_TIMEOUT_MS:
223 save_setting(now)
224
225 show_bits(frame(now))
226
227 # Fixed step: wait until the next 5 ms
228 next_loop = time.ticks_add(next_loop, LOOP_MS)
229 wait = time.ticks_diff(next_loop, time.ticks_ms())
230 if wait > 0:
231 time.sleep_ms(wait)
232 else:
233 next_loop = time.ticks_ms()
234FAQ
Paano ko babasahin ang binary clock?
Mula kaliwa pakanan, 32, 16, 8, 4, 2 at 1 ang halaga ng mga LED. Pagsamahin ang halaga ng mga nakasinding LED: sa pattern na 001101, nakasindi ang 8, 4 at 1, kaya 13 ang value. Hindi lumalampas sa 23 ang oras, kaya laging madilim ang pinakakaliwang LED sa field ng oras. Ipini-print ng serial monitor ang bawat value kasama ang anyo nito sa binary.
Bakit sapat na ang 6 LED?
Nakakabilang ang 6 na bit mula 0 hanggang 63 (2 sa power na 6 = 64 na value). Hanggang 59 ang segundo at minuto at hanggang 23 ang oras, kaya kasya silang lahat sa 6 na bit. Para makita nang sabay ang oras, minuto at segundo, kakailanganin mo ng hiwalay na row ng LED para sa bawat field (17 LED lahat-lahat).
Nare-reset ba ang orasan pagkatapos mawalan ng kuryente?
Oo. Walang orasang may backup na baterya ang Pico, kaya nagsisimula ang code sa `START_TIME` sa bawat boot. Maitatabi ang oras ng RTC module na may backup na baterya gaya ng DS1307. Sa project na ito, maitatakda mo ang oras at minuto gamit ang button sa loob ng ilang segundo pagkabukas.
Puwede ba akong gumamit ng iba't ibang kulay ng LED?
Oo. Maganda ang sindi ng pula, berde, dilaw at orange na LED sa 3.3 V na may 220 Ω. Mga 3 V ang kailangan ng asul at puting LED at puwedeng mukhang malamlam sa 3.3 V; ibaba sa 100 Ω ang resistor nila. Mas madaling basahin ang orasan kapag iba ang kulay ng matataas na puwesto.
