AR-45शुरुआती

DS1302 RTC क्लॉक मॉड्यूल सेट करना

4.5(23)
31 पूरा
DS1302 RTC क्लॉक मॉड्यूल सेट करना
आप एक छोटा क्लॉक मॉड्यूल चालू करते हैं जो Arduino बंद होने पर भी समय नहीं भूलता। मॉड्यूल की अपनी छोटी बैटरी होती है और घड़ी एक बार सेट होने के बाद तारीख और समय हर सेकंड आपके कंप्यूटर स्क्रीन पर लिखे जाते हैं। अलार्म, टाइमर और रिकॉर्ड रखने वाला हर प्रोजेक्ट इसी स्टेप से शुरू होता है।

वीडियो

सर्किट डायग्राम

DS1302 RTC क्लॉक मॉड्यूल सेट करना - सर्किट डायग्राम

सोर्स कोड

C++ (Arduino IDE)
1// ─────────────────────────────────────────
2//   BlueGrays · bluegrays.com
3//   DS1302 RTC Clock Module Setup
4// ─────────────────────────────────────────
5// If the RTC's time is invalid (new module, flat battery) it writes the
6// compile date and time to the DS1302 once, then prints the date and time
7// to the Serial Monitor every second. The module's battery keeps the time
8// with the power off; later starts do not set it again.
9//
10// Pins:
11//   D6 -> RTC CLK
12//   D7 -> RTC DAT
13//   D8 -> RTC RST
14//   RTC VCC to 5V, GND to GND
15
16#include <virtuabotixRTC.h>   // DS1302 library
17
18// Pins: CLK, DAT, RST
19virtuabotixRTC myRTC(6, 7, 8);
20
21void setup() {
22  Serial.begin(9600);   // Serial at 9600 baud
23
24  // Read the RTC first. A year below 2024 or a month outside 1-12 means the time was never set;
25  // write the compile time. If it is valid leave it, so uploading again or power cycling the
26  // Arduino keeps the time.
27  myRTC.updateTime();
28  if (myRTC.year < 2024 || myRTC.month < 1 || myRTC.month > 12) {
29    setFromCompileTime();
30  }
31}
32
33// Writes the compile time (__DATE__ "Oct 28 2026", __TIME__ "13:42:15") to the RTC. Uploading takes
34// a few seconds, so the clock starts that far behind.
35void setFromCompileTime() {
36  const char *date = __DATE__;
37  const char *time = __TIME__;
38  const char *months = "JanFebMarAprMayJunJulAugSepOctNovDec";
39  char monthName[4] = {date[0], date[1], date[2], '\0'};
40
41  int month = (strstr(months, monthName) - months) / 3 + 1;   // "Oct" -> 10
42  int day = atoi(date + 4);
43  int year = atoi(date + 7);
44  int hour = atoi(time);
45  int minute = atoi(time + 3);
46  int second = atoi(time + 6);
47
48  // Day of the week (Sakamoto's method), 0 = Sunday
49  int offsets[] = {0, 3, 2, 5, 0, 3, 5, 1, 4, 6, 2, 4};
50  int y = year - (month < 3);
51  int weekday = (y + y / 4 - y / 100 + y / 400 + offsets[month - 1] + day) % 7;
52  if (weekday == 0) {
53    weekday = 7;   // Monday = 1 ... Sunday = 7
54  }
55
56  // Order: s, min, h, weekday, day, month, year
57  myRTC.setDS1302Time(second, minute, hour, weekday, day, month, year);
58}
59
60void loop() {
61  // Read the current time from the RTC module
62  myRTC.updateTime();
63
64  // Print the time (day/month/year h:m:s)
65  Serial.print("Current Date/Time: ");
66  Serial.print(myRTC.dayofmonth);
67  Serial.print("/");
68  Serial.print(myRTC.month);
69  Serial.print("/");
70  Serial.print(myRTC.year);
71  Serial.print("  ");
72  Serial.print(myRTC.hours);
73  Serial.print(":");
74  Serial.print(myRTC.minutes);
75  Serial.print(":");
76  Serial.println(myRTC.seconds);
77
78  delay(1000);   // Wait 1 s
79}
80

FAQ

RTC मॉड्यूल क्या करता है?

रियल टाइम क्लॉक (RTC) मॉड्यूल अपनी बिल्ट-इन बैटरी की वजह से Arduino बंद होने पर भी समय और तारीख बनाए रखता है। Arduino का millis() काउंटर हर बार पावर मिलने पर शून्य से शुरू होता है, इसलिए सही समय के लिए RTC ज़रूरी है।

क्या समय सिर्फ़ एक बार सेट करना काफ़ी है?

हाँ। कोड पहले मॉड्यूल से समय पढ़ता है; अगर समय कभी सेट नहीं हुआ, तो वह एक बार कोड कंपाइल होने के समय की तारीख और समय लिख देता है। समय सही हो तो वह उसे नहीं छेड़ता, इसलिए दोबारा अपलोड करने या Arduino बंद-चालू करने से घड़ी नहीं बिगड़ती। किसी लाइन को हाथ से कमेंट करने की ज़रूरत नहीं है।

घड़ी पीछे चल रही है, क्या यह सामान्य है?

DS1302 क्रिस्टल पर आधारित है और दिन में कुछ सेकंड आगे-पीछे हो सकता है। ज़्यादा सटीक घड़ी के लिए तापमान के हिसाब से सुधार करने वाला DS3231 मॉड्यूल बेहतर है (साल में लगभग ±1 मिनट)।

मॉड्यूल की बैटरी खत्म होने पर क्या होता है?

Arduino को पावर मिलते रहने तक घड़ी चलती है; अगर पावर कट जाए और बैटरी भी खत्म हो, तो घड़ी रीसेट हो जाती है और दोबारा सेट करनी पड़ती है। CR2032 बैटरी आम तौर पर कुछ साल चलती है।