ES-109शुरुआती

ESP32 Bluetooth तापमान और नमी (DHT11)

ESP32 और DHT11 सेंसर से अपने कमरे का तापमान और नमी फ़ोन पर लाइव देखें: दो रीडिंग बॉक्स और एक चार्ट हर 2 सेकंड में अपडेट होते हैं, इंटरनेट की ज़रूरत नहीं। यह प्रोजेक्ट ऐप के तापमान और नमी Bluetooth टेम्पलेट की स्टेप बाय स्टेप गाइड है। मेरी वर्कशॉप › मेरे डिवाइस › डिवाइस जोड़ें › Bluetooth पर जाएँ, टेम्पलेट चुनें और कोड लें से कोड अपलोड करें। इस पेज का Bluetooth पैनल बनाएँ बटन विज़ार्ड को तैयार हालत में खोलता है।

0.0(0)
ESP32 Bluetooth तापमान और नमी (DHT11)
क्या आपने कभी सोचा है कि आपका कमरा असल में कितना गर्म है, या हवा भारी क्यों लगती है? इस प्रोजेक्ट में आप एक छोटा DHT11 सेंसर तीन तारों से ESP32 से जोड़ते हैं, और बोर्ड हर 2 सेकंड में तापमान और नमी Bluetooth से आपके फ़ोन पर भेजता है। ऐप दो रीडिंग बॉक्स और एक लाइव चार्ट दिखाता है; इंटरनेट, राउटर या सर्वर की ज़रूरत नहीं। सेटअप छोटा है: डिवाइस जोड़ें, Bluetooth, तापमान और नमी टेम्पलेट चुनें, कोड लें से अपलोड करें, फिर अपना बोर्ड खोजें। प्रोजेक्ट पेज का बटन आपको सीधे यह पैनल बनाने पर ले जाता है। आप सीखते हैं: DHT11 से मापना, Bluetooth Low Energy पर डेटा भेजना, सेंसर की गलतियाँ पकड़ना और कभी इंतज़ार न करने वाला टाइमर।

वीडियो

सर्किट डायग्राम

ESP32 Bluetooth तापमान और नमी (DHT11) - सर्किट डायग्राम

सोर्स कोड

C++ (Arduino IDE)
1// ┌───────────────────────────┐
2// │ BlueGrays · bluegrays.com │
3// │ Bluetooth · ESP32         │
4// │ BG-Hava                   │
5// └───────────────────────────┘
6// Temperature and humidity
7// Arduino IDE board: ESP32 Dev Module
8// the BLE library comes with the ESP32 board package, nothing extra to install
9
10#include <BLEDevice.h>
11#include <BLEServer.h>
12#include <BLE2902.h>
13#include <DHT.h>  // Library Manager: 'DHT sensor library' (Adafruit)
14
15const char BLE_NAME[] = "BG-Hava";  // the board advertises with this name, the app finds it in the list by it
16
17// Pins: change them here if you wired differently
18const int DHT_PIN = 4;
19const unsigned long READ_EVERY_MS = 2000;  // a new reading is sent every 2 seconds
20
21void btWrite(const char *text);
22void onValue(const char *key, const char *value);
23void sendAll();
24void onLinkLost();
25
26// ── The app sends "key=value" lines; on "?" the board sends all its values ──
27char line[65];
28uint8_t lineLen = 0;
29unsigned long lastRxMs = 0;
30
31bool is(const char *a, const char *b) { return strcmp(a, b) == 0; }
32bool isOn(const char *v) { return v[0] == '1'; }
33
34void sendText(const char *key, const char *value) {
35  char out[72];
36  snprintf(out, sizeof(out), "%s=%s\n", key, value);
37  btWrite(out);
38}
39
40void sendInt(const char *key, long value) {
41  char text[12];
42  snprintf(text, sizeof(text), "%ld", value);
43  sendText(key, text);
44}
45
46void sendFloat(const char *key, float value) {
47  char text[16];
48  dtostrf(value, 1, 1, text);
49  sendText(key, text);
50}
51
52void handleLine(char *text) {
53  char *eq = strchr(text, '=');
54  if (eq == nullptr) {
55    if (text[strlen(text) - 1] == '?') {
56      btWrite("@v=1.0\n");  // the "@v" line tells the app the code version
57      sendAll();
58    }
59    return;
60  }
61  *eq = '\0';
62  onValue(text, eq + 1);
63}
64
65void feed(char c) {
66  lastRxMs = millis();
67  if (c == '\n' || c == '\r') {
68    if (lineLen == 0) return;
69    line[lineLen] = '\0';
70    lineLen = 0;
71    handleLine(line);
72  } else if (lineLen < sizeof(line) - 1) {
73    line[lineLen++] = c;
74  }
75}
76
77// ── Bluetooth (Nordic UART) ──
78#define UART_SERVICE "6E400001-B5A3-F393-E0A9-E50E24DCCA9E"
79#define UART_RX "6E400002-B5A3-F393-E0A9-E50E24DCCA9E"
80#define UART_TX "6E400003-B5A3-F393-E0A9-E50E24DCCA9E"
81
82BLECharacteristic *txChar = nullptr;
83volatile bool linked = false;
84volatile bool linkLost = false;
85// incoming bytes move from the Bluetooth task to loop() through a small ring buffer
86const int RX_SIZE = 256;
87volatile uint8_t rxBuf[RX_SIZE];
88volatile int rxHead = 0, rxTail = 0;
89
90class ServerEvents : public BLEServerCallbacks {
91  void onConnect(BLEServer *server) override { linked = true; }
92  void onDisconnect(BLEServer *server) override { linked = false; linkLost = true; }
93};
94
95class RxEvents : public BLECharacteristicCallbacks {
96  void onWrite(BLECharacteristic *c) override {
97    auto v = c->getValue();
98    for (size_t i = 0; i < v.length(); i++) {
99      int next = (rxHead + 1) % RX_SIZE;
100      if (next == rxTail) break;
101      rxBuf[rxHead] = (uint8_t)v[i];
102      rxHead = next;
103    }
104  }
105};
106
107// lines go out in 20-byte packets (works with every phone)
108void btWrite(const char *text) {
109  if (!linked || txChar == nullptr) return;
110  size_t n = strlen(text);
111  for (size_t i = 0; i < n; i += 20) {
112    size_t len = n - i < 20 ? n - i : 20;
113    txChar->setValue((uint8_t *)text + i, len);
114    txChar->notify();
115    delay(4);
116  }
117}
118
119void btBegin() {
120  BLEDevice::init(BLE_NAME);
121  BLEServer *server = BLEDevice::createServer();
122  server->setCallbacks(new ServerEvents());
123  BLEService *uart = server->createService(UART_SERVICE);
124  txChar = uart->createCharacteristic(UART_TX, BLECharacteristic::PROPERTY_NOTIFY);
125  txChar->addDescriptor(new BLE2902());
126  BLECharacteristic *rx = uart->createCharacteristic(UART_RX, BLECharacteristic::PROPERTY_WRITE | BLECharacteristic::PROPERTY_WRITE_NR);
127  rx->setCallbacks(new RxEvents());
128  uart->start();
129  BLEAdvertisementData adv;
130  adv.setFlags(0x06);
131  adv.setCompleteServices(BLEUUID(UART_SERVICE));
132  BLEAdvertisementData scan;
133  scan.setName(BLE_NAME);
134  BLEAdvertising *advertising = BLEDevice::getAdvertising();
135  advertising->setAdvertisementData(adv);
136  advertising->setScanResponseData(scan);
137  BLEDevice::startAdvertising();
138}
139
140void btPoll() {
141  while (rxTail != rxHead) {
142    char c = (char)rxBuf[rxTail];
143    rxTail = (rxTail + 1) % RX_SIZE;
144    feed(c);
145  }
146  if (linkLost) {
147    linkLost = false;
148    onLinkLost();
149    delay(100);
150    BLEDevice::startAdvertising();
151  }
152}
153
154// ── ESP32 ──
155DHT dht(DHT_PIN, DHT11);
156float temperature = NAN, humidity = NAN;
157unsigned long lastReadMs = 0;
158
159// if the sensor can't be read the app gets "@err=dht": check the wiring
160void readSensor() {
161  float t = dht.readTemperature();
162  float h = dht.readHumidity();
163  if (isnan(t) || isnan(h)) {
164    btWrite("@err=dht\n");
165    return;
166  }
167  temperature = t;
168  humidity = h;
169}
170
171void sendReadings() {
172  if (isnan(temperature)) return;
173  sendFloat("sicaklik", temperature);
174  sendInt("nem", lround(humidity));
175}
176
177void onValue(const char *key, const char *value) {
178}
179
180void sendAll() {
181  if (isnan(temperature)) readSensor();
182  sendReadings();
183}
184
185void onLinkLost() {
186}
187
188void setup() {
189  Serial.begin(115200);
190  dht.begin();
191  btBegin();
192  Serial.print(F("BlueGrays Bluetooth: "));
193  Serial.println(BLE_NAME);
194}
195
196void loop() {
197  btPoll();
198  if (millis() - lastReadMs >= READ_EVERY_MS) {
199    lastReadMs = millis();
200    readSensor();
201    sendReadings();
202  }
203}
204

FAQ

क्या यह iPhone के साथ चलता है?

हाँ। बोर्ड ESP32 का बिल्ट-इन Bluetooth Low Energy (BLE) इस्तेमाल करता है, और BlueGrays ऐप iPhone और Android दोनों पर उससे जुड़ता है। HC-05 या HC-06 जैसे क्लासिक Bluetooth मॉड्यूल iPhone से कनेक्ट नहीं हो सकते, इसीलिए यह प्रोजेक्ट उन्हें इस्तेमाल नहीं करता। बोर्ड को फ़ोन की Bluetooth सेटिंग्स में पेयर करने की कोशिश न करें; कनेक्शन सिर्फ़ ऐप बनाता है।

क्या DHT11 की जगह DHT22 इस्तेमाल किया जा सकता है?

हाँ। DHT22 (AM2302) ज़्यादा बड़ी रेंज को ज़्यादा सटीकता से मापता है: लगभग -40 से 80 °C, ±0.5 °C। वायरिंग वही रहती है। ऐप का टेम्पलेट DHT11 के लिए बना है, इसलिए DHT dht(DHT_PIN, DHT11) लाइन में DHT11 को DHT22 करें और फिर से अपलोड करें। पैनल के चार्ट का स्केल DHT11 की रेंज (0 से 50 °C) के लिए सेट है।

वैल्यू सिर्फ़ हर 2 सेकंड में क्यों बदलती हैं, और वे कितनी सटीक हैं?

DHT11 को एक सेकंड में एक बार से ज़्यादा नहीं पढ़ा जा सकता, इसलिए कोड READ_EVERY_MS = 2000 से हर 2 सेकंड में मापता और भेजता है। सेंसर 0 से 50 °C और 20% से 90% नमी तक मापता है, लगभग ±2 °C और ±5% नमी की गलती के साथ। कमरे पर नज़र रखने के लिए यह ठीक है; ज़्यादा सटीकता के लिए DHT22 पर जाएँ।

क्या फ़ोन दूर रहने पर रीडिंग सेव होती हैं?

नहीं। बोर्ड सिर्फ़ मौजूदा वैल्यू भेजता है और कोई इतिहास नहीं रखता। चार्ट उन वैल्यू से बनता है जो पैनल खुला और बोर्ड कनेक्ट रहते आती हैं; फ़ोन रेंज से बाहर जाए या आप ऐप बंद करें, तो नए पॉइंट नहीं जुड़ते। दोबारा कनेक्ट करने पर ऐप ? भेजता है और बोर्ड तुरंत अपनी ताज़ा वैल्यू भेज देता है।