Pianino w telefonie przez Bluetooth na ESP32
Telefon jako 8-klawiszowe pianino: klawisz w telefonie, a buzzer pasywny na ESP32 gra tę nutę, bez internetu i Wi-Fi. Ten projekt to przewodnik krok po kroku po szablonie Bluetooth Pianino w telefonie w aplikacji, z buzzerem i dwoma przewodami. Przejdź do Warsztat › Urządzenia › Dodaj urządzenie › Bluetooth, wybierz Pianino w telefonie i wgraj kod przyciskiem Pobierz kod. Przycisk Skonfiguruj jako panel Bluetooth na tej stronie też otwiera kreator z tym szablonem.

Film
Schemat układu

Kod źródłowy
1// ┌───────────────────────────┐
2// │ BlueGrays · bluegrays.com │
3// │ Bluetooth · ESP32 │
4// │ BG-Piyano │
5// └───────────────────────────┘
6// Phone piano
7// Arduino IDE board: ESP32 Dev Module
8// the BLE library comes with the ESP32 board package, nothing extra to install
9
10#include <BLEDevice.h>
11#include <BLEServer.h>
12#include <BLE2902.h>
13
14const char BLE_NAME[] = "BG-Piyano"; // the board advertises with this name, the app finds it in the list by it
15
16// Pins: change them here if you wired differently
17const int BUZZER_PIN = 25; // use a passive buzzer (an active one only makes a single tone)
18
19void btWrite(const char *text);
20void onValue(const char *key, const char *value);
21void sendAll();
22void onLinkLost();
23
24// ── The app sends "key=value" lines; on "?" the board sends all its values ──
25char line[65];
26uint8_t lineLen = 0;
27unsigned long lastRxMs = 0;
28
29bool is(const char *a, const char *b) { return strcmp(a, b) == 0; }
30bool isOn(const char *v) { return v[0] == '1'; }
31
32void sendText(const char *key, const char *value) {
33 char out[72];
34 snprintf(out, sizeof(out), "%s=%s\n", key, value);
35 btWrite(out);
36}
37
38void sendInt(const char *key, long value) {
39 char text[12];
40 snprintf(text, sizeof(text), "%ld", value);
41 sendText(key, text);
42}
43
44void sendFloat(const char *key, float value) {
45 char text[16];
46 dtostrf(value, 1, 1, text);
47 sendText(key, text);
48}
49
50void handleLine(char *text) {
51 char *eq = strchr(text, '=');
52 if (eq == nullptr) {
53 if (text[strlen(text) - 1] == '?') {
54 btWrite("@v=1.0\n"); // the "@v" line tells the app the code version
55 sendAll();
56 }
57 return;
58 }
59 *eq = '\0';
60 onValue(text, eq + 1);
61}
62
63void feed(char c) {
64 lastRxMs = millis();
65 if (c == '\n' || c == '\r') {
66 if (lineLen == 0) return;
67 line[lineLen] = '\0';
68 lineLen = 0;
69 handleLine(line);
70 } else if (lineLen < sizeof(line) - 1) {
71 line[lineLen++] = c;
72 }
73}
74
75// ── Bluetooth (Nordic UART) ──
76#define UART_SERVICE "6E400001-B5A3-F393-E0A9-E50E24DCCA9E"
77#define UART_RX "6E400002-B5A3-F393-E0A9-E50E24DCCA9E"
78#define UART_TX "6E400003-B5A3-F393-E0A9-E50E24DCCA9E"
79
80BLECharacteristic *txChar = nullptr;
81volatile bool linked = false;
82volatile bool linkLost = false;
83// incoming bytes move from the Bluetooth task to loop() through a small ring buffer
84const int RX_SIZE = 256;
85volatile uint8_t rxBuf[RX_SIZE];
86volatile int rxHead = 0, rxTail = 0;
87
88class ServerEvents : public BLEServerCallbacks {
89 void onConnect(BLEServer *server) override { linked = true; }
90 void onDisconnect(BLEServer *server) override { linked = false; linkLost = true; }
91};
92
93class RxEvents : public BLECharacteristicCallbacks {
94 void onWrite(BLECharacteristic *c) override {
95 auto v = c->getValue();
96 for (size_t i = 0; i < v.length(); i++) {
97 int next = (rxHead + 1) % RX_SIZE;
98 if (next == rxTail) break;
99 rxBuf[rxHead] = (uint8_t)v[i];
100 rxHead = next;
101 }
102 }
103};
104
105// lines go out in 20-byte packets (works with every phone)
106void btWrite(const char *text) {
107 if (!linked || txChar == nullptr) return;
108 size_t n = strlen(text);
109 for (size_t i = 0; i < n; i += 20) {
110 size_t len = n - i < 20 ? n - i : 20;
111 txChar->setValue((uint8_t *)text + i, len);
112 txChar->notify();
113 delay(4);
114 }
115}
116
117void btBegin() {
118 BLEDevice::init(BLE_NAME);
119 BLEServer *server = BLEDevice::createServer();
120 server->setCallbacks(new ServerEvents());
121 BLEService *uart = server->createService(UART_SERVICE);
122 txChar = uart->createCharacteristic(UART_TX, BLECharacteristic::PROPERTY_NOTIFY);
123 txChar->addDescriptor(new BLE2902());
124 BLECharacteristic *rx = uart->createCharacteristic(UART_RX, BLECharacteristic::PROPERTY_WRITE | BLECharacteristic::PROPERTY_WRITE_NR);
125 rx->setCallbacks(new RxEvents());
126 uart->start();
127 BLEAdvertisementData adv;
128 adv.setFlags(0x06);
129 adv.setCompleteServices(BLEUUID(UART_SERVICE));
130 BLEAdvertisementData scan;
131 scan.setName(BLE_NAME);
132 BLEAdvertising *advertising = BLEDevice::getAdvertising();
133 advertising->setAdvertisementData(adv);
134 advertising->setScanResponseData(scan);
135 BLEDevice::startAdvertising();
136}
137
138void btPoll() {
139 while (rxTail != rxHead) {
140 char c = (char)rxBuf[rxTail];
141 rxTail = (rxTail + 1) % RX_SIZE;
142 feed(c);
143 }
144 if (linkLost) {
145 linkLost = false;
146 onLinkLost();
147 delay(100);
148 BLEDevice::startAdvertising();
149 }
150}
151
152// ── ESP32 ──
153void onValue(const char *key, const char *value) {
154 if (is(key, "nota")) { // "nota=Hz" plays the note, "nota=0" stops it
155 int hz = atoi(value);
156 if (hz > 0) tone(BUZZER_PIN, hz);
157 else noTone(BUZZER_PIN);
158 }
159}
160
161void sendAll() {
162 sendInt("nota", 0);
163}
164
165void onLinkLost() {
166 noTone(BUZZER_PIN); // Connection lost: the sound stops
167}
168
169void setup() {
170 Serial.begin(115200);
171 pinMode(BUZZER_PIN, OUTPUT);
172 btBegin();
173 Serial.print(F("BlueGrays Bluetooth: "));
174 Serial.println(BLE_NAME);
175}
176
177void loop() {
178 btPoll();
179}
180FAQ
Czy działa z iPhonem?
Tak. Wbudowany w ESP32 Bluetooth Low Energy (BLE) rozmawia i z iPhonem, i z Androidem. iPhone nie łączy się z klasycznymi modułami Bluetooth, takimi jak HC-05 i HC-06, a ten projekt ich nie potrzebuje. Nie próbuj parować płytki w ustawieniach Bluetooth telefonu; płytki BLE mogą się tam nie pojawiać i to normalne. Połączenie nawiązuje aplikacja BlueGrays.
Czym różni się buzzer aktywny od pasywnego i którego potrzebuję?
Potrzebujesz buzzera pasywnego. Buzzer pasywny działa jak malutki głośnik: gra każdą częstotliwość, którą mu wyślesz. Buzzer aktywny ma w środku własny układ i po podaniu zasilania wydaje zawsze ten sam, stały dźwięk, więc klawiszy nie da się odróżnić. Ten projekt pokaże ci, który masz: jeśli klawisze grają różne nuty, buzzer jest pasywny, a jeśli każdy klawisz daje to samo brzęczenie, jest aktywny. Przy zakupie szukaj w nazwie produktu słowa pasywny.
Czy mogę nacisnąć dwa klawisze naraz i zagrać akord?
Nie. Buzzer gra naraz tylko jedną częstotliwość, a polecenie tone na płytce wytwarza pojedynczą nutę. Gdy naciśniesz dwa klawisze jednocześnie, nuty się nie nakładają; płytka gra tylko tę, która przyszła ostatnia. Graj melodie nuta po nucie. Przycisk Graj na pełnym ekranie w panelu powiększa klawisze, a tam możesz też przesuwać palcem po klawiszach, żeby płynnie przechodzić od nuty do nuty.
Czy mogę dodać inne nuty albo więcej klawiszy?
Osiem klawiszy w panelu jest stałych: od niskiego do wysokiego C, bez krzyżyków i bemoli, a w aplikacji nie da się dodać klawiszy. Strona płytki jest za to elastyczna: kod gra jako częstotliwość każdą dodatnią liczbę przychodzącą z telefonu i milknie, gdy dostanie 0. Możesz więc zmienić dźwięk w kodzie; na przykład pomnóż przychodzącą częstotliwość przez dwa, a całe pianino przesunie się o oktawę w górę.
