AR-45Początkujący

Uruchomienie modułu zegara RTC DS1302

4.5(23)
31 ukończone
Uruchomienie modułu zegara RTC DS1302
Uruchamiasz mały moduł zegara, który nigdy nie zapomina godziny, nawet gdy Arduino jest wyłączone. Moduł ma własną małą baterię, a po ustawieniu zegara data i godzina co sekundę pojawiają się na ekranie komputera. Od tego kroku zaczynają się budziki, timery i wszystkie projekty, które prowadzą zapis.

Film

Schemat układu

Uruchomienie modułu zegara RTC DS1302 - Schemat układu

Kod źródłowy

C++ (Arduino IDE)
1// ─────────────────────────────────────────
2//   BlueGrays · bluegrays.com
3//   DS1302 RTC Clock Module Setup
4// ─────────────────────────────────────────
5// If the RTC's time is invalid (new module, flat battery) it writes the
6// compile date and time to the DS1302 once, then prints the date and time
7// to the Serial Monitor every second. The module's battery keeps the time
8// with the power off; later starts do not set it again.
9//
10// Pins:
11//   D6 -> RTC CLK
12//   D7 -> RTC DAT
13//   D8 -> RTC RST
14//   RTC VCC to 5V, GND to GND
15
16#include <virtuabotixRTC.h>   // DS1302 library
17
18// Pins: CLK, DAT, RST
19virtuabotixRTC myRTC(6, 7, 8);
20
21void setup() {
22  Serial.begin(9600);   // Serial at 9600 baud
23
24  // Read the RTC first. A year below 2024 or a month outside 1-12 means the time was never set;
25  // write the compile time. If it is valid leave it, so uploading again or power cycling the
26  // Arduino keeps the time.
27  myRTC.updateTime();
28  if (myRTC.year < 2024 || myRTC.month < 1 || myRTC.month > 12) {
29    setFromCompileTime();
30  }
31}
32
33// Writes the compile time (__DATE__ "Oct 28 2026", __TIME__ "13:42:15") to the RTC. Uploading takes
34// a few seconds, so the clock starts that far behind.
35void setFromCompileTime() {
36  const char *date = __DATE__;
37  const char *time = __TIME__;
38  const char *months = "JanFebMarAprMayJunJulAugSepOctNovDec";
39  char monthName[4] = {date[0], date[1], date[2], '\0'};
40
41  int month = (strstr(months, monthName) - months) / 3 + 1;   // "Oct" -> 10
42  int day = atoi(date + 4);
43  int year = atoi(date + 7);
44  int hour = atoi(time);
45  int minute = atoi(time + 3);
46  int second = atoi(time + 6);
47
48  // Day of the week (Sakamoto's method), 0 = Sunday
49  int offsets[] = {0, 3, 2, 5, 0, 3, 5, 1, 4, 6, 2, 4};
50  int y = year - (month < 3);
51  int weekday = (y + y / 4 - y / 100 + y / 400 + offsets[month - 1] + day) % 7;
52  if (weekday == 0) {
53    weekday = 7;   // Monday = 1 ... Sunday = 7
54  }
55
56  // Order: s, min, h, weekday, day, month, year
57  myRTC.setDS1302Time(second, minute, hour, weekday, day, month, year);
58}
59
60void loop() {
61  // Read the current time from the RTC module
62  myRTC.updateTime();
63
64  // Print the time (day/month/year h:m:s)
65  Serial.print("Current Date/Time: ");
66  Serial.print(myRTC.dayofmonth);
67  Serial.print("/");
68  Serial.print(myRTC.month);
69  Serial.print("/");
70  Serial.print(myRTC.year);
71  Serial.print("  ");
72  Serial.print(myRTC.hours);
73  Serial.print(":");
74  Serial.print(myRTC.minutes);
75  Serial.print(":");
76  Serial.println(myRTC.seconds);
77
78  delay(1000);   // Wait 1 s
79}
80

FAQ

Do czego służy moduł RTC?

Moduł zegara czasu rzeczywistego (RTC) dzięki wbudowanej baterii przechowuje godzinę i datę nawet wtedy, gdy Arduino jest wyłączone. Licznik millis() w Arduino zeruje się przy każdym włączeniu, dlatego do dokładnego czasu potrzebny jest RTC.

Czy wystarczy ustawić czas tylko raz?

Tak. Kod najpierw odczytuje czas z modułu; jeśli nigdy nie był ustawiony, zapisuje datę i godzinę kompilacji kodu. Jeśli czas jest prawidłowy, zostawia go bez zmian, więc ponowne wgranie ani wyłączenie i włączenie Arduino nie psuje zegara. Nie musisz ręcznie zamieniać żadnej linii w komentarz.

Zegar się spóźnia. Czy to normalne?

DS1302 działa na krysztale kwarcowym i może się mylić o kilka sekund na dobę. Do dokładniejszego zegara zaleca się moduł DS3231 z kompensacją temperatury (około ±1 minuty na rok).

Co się stanie, gdy bateria w module się rozładuje?

Zegar działa, dopóki Arduino jest zasilane; jeśli zasilanie zniknie, a bateria będzie rozładowana, zegar się wyzeruje i trzeba go ustawić od nowa. Bateria CR2032 wystarcza zwykle na kilka lat.