AR-45Початківець

Налаштування модуля годинника RTC DS1302

4.5(23)
31 готово
Налаштування модуля годинника RTC DS1302
Ти запускаєш маленький модуль годинника, який ніколи не забуває час, навіть коли Arduino вимкнено. Модуль має власну крихітну батарейку, і коли годинник налаштовано, дата й час щосекунди виводяться на екран комп’ютера. Будильники, таймери й усі проєкти з журналом подій починаються з цього кроку.

Відео

Схема

Налаштування модуля годинника RTC DS1302 - Схема

Вихідний код

C++ (Arduino IDE)
1// ─────────────────────────────────────────
2//   BlueGrays · bluegrays.com
3//   DS1302 RTC Clock Module Setup
4// ─────────────────────────────────────────
5// If the RTC's time is invalid (new module, flat battery) it writes the
6// compile date and time to the DS1302 once, then prints the date and time
7// to the Serial Monitor every second. The module's battery keeps the time
8// with the power off; later starts do not set it again.
9//
10// Pins:
11//   D6 -> RTC CLK
12//   D7 -> RTC DAT
13//   D8 -> RTC RST
14//   RTC VCC to 5V, GND to GND
15
16#include <virtuabotixRTC.h>   // DS1302 library
17
18// Pins: CLK, DAT, RST
19virtuabotixRTC myRTC(6, 7, 8);
20
21void setup() {
22  Serial.begin(9600);   // Serial at 9600 baud
23
24  // Read the RTC first. A year below 2024 or a month outside 1-12 means the time was never set;
25  // write the compile time. If it is valid leave it, so uploading again or power cycling the
26  // Arduino keeps the time.
27  myRTC.updateTime();
28  if (myRTC.year < 2024 || myRTC.month < 1 || myRTC.month > 12) {
29    setFromCompileTime();
30  }
31}
32
33// Writes the compile time (__DATE__ "Oct 28 2026", __TIME__ "13:42:15") to the RTC. Uploading takes
34// a few seconds, so the clock starts that far behind.
35void setFromCompileTime() {
36  const char *date = __DATE__;
37  const char *time = __TIME__;
38  const char *months = "JanFebMarAprMayJunJulAugSepOctNovDec";
39  char monthName[4] = {date[0], date[1], date[2], '\0'};
40
41  int month = (strstr(months, monthName) - months) / 3 + 1;   // "Oct" -> 10
42  int day = atoi(date + 4);
43  int year = atoi(date + 7);
44  int hour = atoi(time);
45  int minute = atoi(time + 3);
46  int second = atoi(time + 6);
47
48  // Day of the week (Sakamoto's method), 0 = Sunday
49  int offsets[] = {0, 3, 2, 5, 0, 3, 5, 1, 4, 6, 2, 4};
50  int y = year - (month < 3);
51  int weekday = (y + y / 4 - y / 100 + y / 400 + offsets[month - 1] + day) % 7;
52  if (weekday == 0) {
53    weekday = 7;   // Monday = 1 ... Sunday = 7
54  }
55
56  // Order: s, min, h, weekday, day, month, year
57  myRTC.setDS1302Time(second, minute, hour, weekday, day, month, year);
58}
59
60void loop() {
61  // Read the current time from the RTC module
62  myRTC.updateTime();
63
64  // Print the time (day/month/year h:m:s)
65  Serial.print("Current Date/Time: ");
66  Serial.print(myRTC.dayofmonth);
67  Serial.print("/");
68  Serial.print(myRTC.month);
69  Serial.print("/");
70  Serial.print(myRTC.year);
71  Serial.print("  ");
72  Serial.print(myRTC.hours);
73  Serial.print(":");
74  Serial.print(myRTC.minutes);
75  Serial.print(":");
76  Serial.println(myRTC.seconds);
77
78  delay(1000);   // Wait 1 s
79}
80

Поширені запитання

Що робить модуль RTC?

Модуль годинника реального часу (RTC) завдяки вбудованій батарейці зберігає час і дату навіть тоді, коли Arduino вимкнено. Лічильник millis() Arduino обнуляється щоразу після ввімкнення, тому для точного часу потрібен RTC.

Чи досить налаштувати час лише один раз?

Так. Код спершу зчитує час з модуля; якщо його ніколи не встановлювали, він один раз записує дату й час компіляції коду. Якщо час правильний, код його не чіпає, тож повторне завантаження чи вимкнення й увімкнення Arduino годинник не збиває. Коментувати якийсь рядок вручну не потрібно.

Годинник відстає. Це нормально?

DS1302 працює від кварцу й може відхилятися на кілька секунд на добу. Для точнішого годинника радимо модуль DS3231 з термокомпенсацією (приблизно ±1 хвилина на рік).

Що буде, коли сяде батарейка в модулі?

Годинник іде, поки Arduino має живлення; якщо живлення вимкнено, а батарейка сіла, годинник скидається, і його треба налаштувати знову. Батарейки CR2032 зазвичай вистачає на кілька років.