ESP32 Bluetooth Car (L298N)
Drive a two-wheel car over Bluetooth with the joystick on your phone; no internet needed, works on iPhone and Android. This project is the step-by-step guide to the Car remote Bluetooth template in the app, built with an ESP32, an L298N and two motors. Go to Workshop › Devices › Add a device › Bluetooth, pick Car remote and upload the code from Get the code. The Set up as a Bluetooth panel button on this page opens the wizard with this template.

Video
Circuit Diagram

Source Code
1// ┌───────────────────────────┐
2// │ BlueGrays · bluegrays.com │
3// │ Bluetooth · ESP32 │
4// │ BG-Araba │
5// └───────────────────────────┘
6// Car remote
7// Arduino IDE board: ESP32 Dev Module
8// the BLE library comes with the ESP32 board package, nothing extra to install
9
10#include <BLEDevice.h>
11#include <BLEServer.h>
12#include <BLE2902.h>
13
14const char BLE_NAME[] = "BG-Araba"; // the board advertises with this name, the app finds it in the list by it
15
16// Pins: change them here if you wired differently
17const int ENA = 14, IN1 = 27, IN2 = 26; // Motor A (ENA, IN1, IN2) is the left wheel, motor B (ENB, IN3, IN4) the right one
18const int ENB = 32, IN3 = 25, IN4 = 33;
19const unsigned long COMMAND_TIMEOUT_MS = 500; // Safety: the motors stop if no command arrives for 500 ms (the app repeats it while you drive)
20
21void btWrite(const char *text);
22void onValue(const char *key, const char *value);
23void sendAll();
24void onLinkLost();
25
26// ── The app sends "key=value" lines; on "?" the board sends all its values ──
27char line[65];
28uint8_t lineLen = 0;
29unsigned long lastRxMs = 0;
30
31bool is(const char *a, const char *b) { return strcmp(a, b) == 0; }
32bool isOn(const char *v) { return v[0] == '1'; }
33
34void sendText(const char *key, const char *value) {
35 char out[72];
36 snprintf(out, sizeof(out), "%s=%s\n", key, value);
37 btWrite(out);
38}
39
40void sendInt(const char *key, long value) {
41 char text[12];
42 snprintf(text, sizeof(text), "%ld", value);
43 sendText(key, text);
44}
45
46void sendFloat(const char *key, float value) {
47 char text[16];
48 dtostrf(value, 1, 1, text);
49 sendText(key, text);
50}
51
52void handleLine(char *text) {
53 char *eq = strchr(text, '=');
54 if (eq == nullptr) {
55 if (text[strlen(text) - 1] == '?') {
56 btWrite("@v=1.0\n"); // the "@v" line tells the app the code version
57 sendAll();
58 }
59 return;
60 }
61 *eq = '\0';
62 onValue(text, eq + 1);
63}
64
65void feed(char c) {
66 lastRxMs = millis();
67 if (c == '\n' || c == '\r') {
68 if (lineLen == 0) return;
69 line[lineLen] = '\0';
70 lineLen = 0;
71 handleLine(line);
72 } else if (lineLen < sizeof(line) - 1) {
73 line[lineLen++] = c;
74 }
75}
76
77// ── Bluetooth (Nordic UART) ──
78#define UART_SERVICE "6E400001-B5A3-F393-E0A9-E50E24DCCA9E"
79#define UART_RX "6E400002-B5A3-F393-E0A9-E50E24DCCA9E"
80#define UART_TX "6E400003-B5A3-F393-E0A9-E50E24DCCA9E"
81
82BLECharacteristic *txChar = nullptr;
83volatile bool linked = false;
84volatile bool linkLost = false;
85// incoming bytes move from the Bluetooth task to loop() through a small ring buffer
86const int RX_SIZE = 256;
87volatile uint8_t rxBuf[RX_SIZE];
88volatile int rxHead = 0, rxTail = 0;
89
90class ServerEvents : public BLEServerCallbacks {
91 void onConnect(BLEServer *server) override { linked = true; }
92 void onDisconnect(BLEServer *server) override { linked = false; linkLost = true; }
93};
94
95class RxEvents : public BLECharacteristicCallbacks {
96 void onWrite(BLECharacteristic *c) override {
97 auto v = c->getValue();
98 for (size_t i = 0; i < v.length(); i++) {
99 int next = (rxHead + 1) % RX_SIZE;
100 if (next == rxTail) break;
101 rxBuf[rxHead] = (uint8_t)v[i];
102 rxHead = next;
103 }
104 }
105};
106
107// lines go out in 20-byte packets (works with every phone)
108void btWrite(const char *text) {
109 if (!linked || txChar == nullptr) return;
110 size_t n = strlen(text);
111 for (size_t i = 0; i < n; i += 20) {
112 size_t len = n - i < 20 ? n - i : 20;
113 txChar->setValue((uint8_t *)text + i, len);
114 txChar->notify();
115 delay(4);
116 }
117}
118
119void btBegin() {
120 BLEDevice::init(BLE_NAME);
121 BLEServer *server = BLEDevice::createServer();
122 server->setCallbacks(new ServerEvents());
123 BLEService *uart = server->createService(UART_SERVICE);
124 txChar = uart->createCharacteristic(UART_TX, BLECharacteristic::PROPERTY_NOTIFY);
125 txChar->addDescriptor(new BLE2902());
126 BLECharacteristic *rx = uart->createCharacteristic(UART_RX, BLECharacteristic::PROPERTY_WRITE | BLECharacteristic::PROPERTY_WRITE_NR);
127 rx->setCallbacks(new RxEvents());
128 uart->start();
129 BLEAdvertisementData adv;
130 adv.setFlags(0x06);
131 adv.setCompleteServices(BLEUUID(UART_SERVICE));
132 BLEAdvertisementData scan;
133 scan.setName(BLE_NAME);
134 BLEAdvertising *advertising = BLEDevice::getAdvertising();
135 advertising->setAdvertisementData(adv);
136 advertising->setScanResponseData(scan);
137 BLEDevice::startAdvertising();
138}
139
140void btPoll() {
141 while (rxTail != rxHead) {
142 char c = (char)rxBuf[rxTail];
143 rxTail = (rxTail + 1) % RX_SIZE;
144 feed(c);
145 }
146 if (linkLost) {
147 linkLost = false;
148 onLinkLost();
149 delay(100);
150 BLEDevice::startAdvertising();
151 }
152}
153
154// ── ESP32 ──
155int speedLimit = 80; // speed limit from the app (0–100 %)
156unsigned long lastCommandMs = 0;
157bool moving = false;
158
159// if the car drives backwards, swap that motor's two wires
160void motor(int en, int a, int b, int power) {
161 power = constrain(power, -100, 100);
162 digitalWrite(a, power > 0 ? HIGH : LOW);
163 digitalWrite(b, power < 0 ? HIGH : LOW);
164 analogWrite(en, abs(power) * speedLimit * 255L / 10000);
165}
166
167void drive(int left, int right) {
168 motor(ENA, IN1, IN2, left);
169 motor(ENB, IN3, IN4, right);
170 moving = left != 0 || right != 0;
171 lastCommandMs = millis();
172}
173
174void onValue(const char *key, const char *value) {
175 if (is(key, "joy")) { // Joystick: y is forward/back, x turns; mixed into left and right wheel speeds
176 const char *comma = strchr(value, ',');
177 int x = atoi(value), y = comma ? atoi(comma + 1) : 0;
178 drive(constrain(y + x, -100, 100), constrain(y - x, -100, 100));
179 } else if (is(key, "yon")) {
180 if (is(value, "ileri")) drive(100, 100);
181 else if (is(value, "geri")) drive(-100, -100);
182 else if (is(value, "sol")) drive(-70, 70);
183 else if (is(value, "sag")) drive(70, -70);
184 else drive(0, 0);
185 } else if (is(key, "hiz")) {
186 speedLimit = constrain(atoi(value), 0, 100);
187 }
188}
189
190void sendAll() {
191 sendInt("hiz", speedLimit);
192}
193
194void onLinkLost() {
195 drive(0, 0); // Connection lost: the motors stop
196}
197
198void setup() {
199 Serial.begin(115200);
200 int pins[] = { ENA, IN1, IN2, ENB, IN3, IN4 };
201 for (int pin : pins) pinMode(pin, OUTPUT);
202 drive(0, 0);
203 btBegin();
204 Serial.print(F("BlueGrays Bluetooth: "));
205 Serial.println(BLE_NAME);
206}
207
208void loop() {
209 btPoll();
210 if (moving && millis() - lastCommandMs > COMMAND_TIMEOUT_MS) drive(0, 0);
211}
212FAQ
Does it work with an iPhone? How is it different from HC-05?
Yes, it works on iPhone and Android. Classic Bluetooth modules such as the HC-05 and HC-06 cannot connect to an iPhone, so this project uses the ESP32's built-in Bluetooth Low Energy and needs no extra module. Do not try to pair the board in your phone's Bluetooth settings; only the BlueGrays app makes the connection.
The car drives backwards or one wheel spins the wrong way.
Swap the two wires of the motor that turns the wrong way at the L298N screw terminal (left motor OUT1/OUT2, right motor OUT3/OUT4); the comment in the code says the same. If the car spins on the spot when you press forward, only one motor is reversed. If both turn the right way but left steers right, swap the left and right motors.
How do I power the ESP32? Can USB and the battery be connected at the same time?
The 2× 18650 batteries (7.4 V) go to the L298N's 12V input, and the L298N's 5V output feeds the ESP32's VIN pin; for that the 5V regulator jumper on the L298N must stay on. This way the car runs without a cable. If USB is plugged in while you upload, switch the battery off or pull the 5V wire so the two supplies do not clash. The L298N GND and the ESP32 GND must always be connected.
What is the range? What does the car do if the connection drops?
Bluetooth Low Energy usually reaches 10 to 30 metres in the open; walls and people in the way shorten that. If the connection drops, the board stops the motors at once and starts advertising again, so you can reconnect from the app. The car also stops if the board gets no command for 500 ms, so it never runs off out of range.
